Difference between revisions of "CC Phoenix Edge RPM output/de"

From Spirit System Manual
Jump to: navigation, search
(Created page with "Verdrahtung")
(Created page with "Öffnen Sie in den Spirit Settings das Fenster "General - Throttle/Governor" und stellen Sie folgendes ein: * ''Throttle Frequency'': 60Hz. * ''Throttle Range - Min.: 1060 us....")
 
(5 intermediate revisions by the same user not shown)
Line 15: Line 15:
  
 
; Verdrahtung
 
; Verdrahtung
: White wire: RPM Output Signal (PIT pin)
+
: Weißes Kabel: RPM-Ausgangssignal (PIT-Pin)
: Yellow wire: Throttle signal (AUX1 port)
+
: Gelbes Kabel: Throttle Signal (AUX1-Anschluss)
: Red wire: BEC Voltage (AUX1 port)
+
: Rotes Kabel: BEC-Spannung (AUX1-Anschluss)
: Brown wire: Ground (AUX1 port)
+
: Braunes Kabel: Masse (AUX1-Anschluss)
  
 
[[File:cc-connection.jpg|500px|]]
 
[[File:cc-connection.jpg|500px|]]
Line 30: Line 30:
 
After this, you can enable Governor in the Spirit unit.
 
After this, you can enable Governor in the Spirit unit.
  
== Governor Settings ==
+
== Governor-Einstellungen ==
  
In the Spirit Settings open the ''General - Throttle/Governor'' window and set the following:
+
Öffnen Sie in den Spirit Settings das Fenster "General - Throttle/Governor" und stellen Sie folgendes ein:
 
* ''Throttle Frequency'': 60Hz.
 
* ''Throttle Frequency'': 60Hz.
 
* ''Throttle Range - Min.: 1060 us.
 
* ''Throttle Range - Min.: 1060 us.
 
* ''Throttle Range - Max.: 1940 us.
 
* ''Throttle Range - Max.: 1940 us.

Latest revision as of 14:29, 9 May 2018

Other languages:
Deutsch • ‎English • ‎magyar • ‎italiano • ‎русский

Castle Creations Phoenix ESCs sind mit einem RPM-Kabel ausgestattet, das das Signal für den externen Regler liefert. Sie müssen also nichts anderes tun, als die Kabel richtig anzuschließen und den internen Regler des ESC abzuschalten.

Cc-esc.jpg

1 Erforderliche Änderung

Für die Verwendung mit den Spirit-Geräten ist eine kleine Modifikation des RPM-Kabels erforderlich.

  • Verlegen Sie das weiße Kabel in die Mitte des Servosteckers.
  • Das geht ganz einfach mit einer Nadel.

Cc-sensor.jpg

Verdrahtung
Weißes Kabel: RPM-Ausgangssignal (PIT-Pin)
Gelbes Kabel: Throttle Signal (AUX1-Anschluss)
Rotes Kabel: BEC-Spannung (AUX1-Anschluss)
Braunes Kabel: Masse (AUX1-Anschluss)

Cc-connection.jpg

Connect the cables according the photo now.

2 Changing ESC settings

It is very important to change ESC mode so that internal Governor is disabled. This can be done by Castle Link software.

After this, you can enable Governor in the Spirit unit.

3 Governor-Einstellungen

Öffnen Sie in den Spirit Settings das Fenster "General - Throttle/Governor" und stellen Sie folgendes ein:

  • Throttle Frequency: 60Hz.
  • Throttle Range - Min.: 1060 us.
  • Throttle Range - Max.: 1940 us.