Difference between revisions of "Castle Telemetry/ru"

From Spirit System Manual
Jump to: navigation, search
(Created page with "Для настройки регулятора понадобится кабель подключения и программа [http://www.castlecreations.com/downloads Castl...")
(Created page with "Телеметрийный кабель.")
Line 10: Line 10:
 
[[File:castlelink.jpg]]
 
[[File:castlelink.jpg]]
  
== Telemetry Cable ==
+
== Телеметрийный кабель. ==
 
To allow the telemetry data transmission '''Telem CC cable''' is required. This cable is available in our [http://store.spirit-system.com/en/accessories/36-telemcc-cable.html Eshop].
 
To allow the telemetry data transmission '''Telem CC cable''' is required. This cable is available in our [http://store.spirit-system.com/en/accessories/36-telemcc-cable.html Eshop].
  

Revision as of 13:41, 15 October 2018

Other languages:
čeština • ‎Deutsch • ‎English • ‎español • ‎français • ‎magyar • ‎italiano • ‎русский

Регуляторы Castle Creations имеют функцию под названием Link Live. Она обеспечивает двустороннюю передачу данных по кабелю управления газом. Эта функция отключена по умолчанию, и ее необходимо включить перед использованием. Данная функция подразумевает, что устройство на другом конце кабеля поддерживает прием данных. В противном случае, сигнал газа будет игнорироваться.

1 Настройка регулятора

Для настройки регулятора понадобится кабель подключения и программа Castle Link software Затем необходимо активировать функцию Link-Live

Castlelink.jpg

2 Телеметрийный кабель.

To allow the telemetry data transmission Telem CC cable is required. This cable is available in our Eshop.

Telemcc.png

For Experts: Alternatively you can modify your current Throttle cable by adding 10kOhm resistor between white (signal) and red (+) wires. In this case the Telemetry cable is not required.

3 Interfacing

Connect the Telemetry cable to the AUX(1) port in the unit, where you normally connect the Throttle cable of the ESC. Connect the Throttle cable to the end of the Telem CC cable.

4 Spirit Settings

4.1 Throttle Assignment

Once cable is connected, it is absolutely necessary to assign the Throttle (if not assigned yet).

Power up the ESC and start the Spirit Settings as usually.

Go to the General/Channels and assign a channel to the Throttle.

Throttle-assign.png

4.2 Telemetry activation

As the last step you have to set the ESC Telemetry in the Spirit Settings software.

Go to the Advanced/Telemetry settings and set the Castle Creations Phoenix & Talon option.

Esc-telem.png

Then close the window and save the settings (CTRL+S). Finally, reconnect battery from the ESC.

From this moment, everything should work.

5 Displaying telemetry data

You can display telemetry data directly in your radio from now.

How to display the data is described in the integration guides:

6 Supported models

Model

Battery Voltage

Battery Current

BEC Voltage

Consumed Capacity

ESC Temperature

RPM

Phoenix Edge 50
Phoenix Edge 75
Phoenix Edge 100
Phoenix Edge 130
Phoenix Edge HV 40
Phoenix Edge HV 80
Phoenix Edge HV 120
Phoenix Edge HV 160
Phoenix Edge HVF 160
Phoenix Edge Lite 50
Phoenix Edge Lite 75
Phoenix Edge Lite 100
Phoenix Edge Lite 130
Phoenix Edge Lite HV 40
Phoenix Edge Lite HV 80
Phoenix Edge Lite HV 120
Phoenix Edge Lite HV 160
Phoenix Talon 15 x x
Phoenix Talon 25 x x
Phoenix Talon 35 x x
Phoenix Talon 90 x x
Phoenix Talon HV 120 x x

Info.png Consumed Capacity is calculated from the Current Consumption.