Difference between revisions of "Futaba"

From Spirit System Manual
Jump to: navigation, search
(Marked this version for translation)
Line 3: Line 3:
  
 
<div align=center><font size="6">
 
<div align=center><font size="6">
<translate>Setup guide</translate></font></div>
+
<translate><!--T:1-->
 +
Setup guide</translate></font></div>
 
<div align=center><font size="5">
 
<div align=center><font size="5">
 
for</font></div>
 
for</font></div>
 
[[File:F1.jpg|center]]
 
[[File:F1.jpg|center]]
<div align=center><font size="4">T8FG <translate>or compatible</translate></font>
+
<div align=center><font size="4">T8FG <translate><!--T:2-->
 +
or compatible</translate></font>
 
</div>
 
</div>
  
 
<br />
 
<br />
 
<div align=center>
 
<div align=center>
✔<translate>Flight Modes</translate><br />
+
✔<translate><!--T:3-->
✔<translate>Gyro Gains</translate><br />
+
Flight Modes</translate><br />
✔<translate>Normal (Rate) mode</translate><br />
+
✔<translate><!--T:4-->
✔<translate>Rescue and Stabiilsation</translate><br />
+
Gyro Gains</translate><br />
✔<translate>Bank Switching</translate><br />
+
✔<translate><!--T:5-->
 +
Normal (Rate) mode</translate><br />
 +
✔<translate><!--T:6-->
 +
Rescue and Stabiilsation</translate><br />
 +
✔<translate><!--T:7-->
 +
Bank Switching</translate><br />
 
</div>
 
</div>
  
== <translate>Flight Mode setup</translate> ==
+
== <translate><!--T:8-->
 +
Flight Mode setup</translate> ==
  
'''<translate>Go to MDL  →  CONDITION</translate>'''
+
'''<translate><!--T:9-->
 +
Go to MDL  →  CONDITION</translate>'''
  
<translate>Set the Flight mode switch SE for IDLEUP1 and IDLEUP2.
+
<translate><!--T:10-->
 +
Set the Flight mode switch SE for IDLEUP1 and IDLEUP2.
 
:* Make sure that ON/OFF for IDLEUP1 is configured in the following way:
 
:* Make sure that ON/OFF for IDLEUP1 is configured in the following way:
 
:::OFF
 
:::OFF
Line 29: Line 39:
 
:::OFF
 
:::OFF
  
 +
<!--T:11-->
 
:* For IDLEUP2 it should be as following:
 
:* For IDLEUP2 it should be as following:
 
:::OFF
 
:::OFF
Line 34: Line 45:
 
:::ON
 
:::ON
  
 +
<!--T:12-->
 
:*IDLEUP3 will be used for the Rescue/Stabilisation modes. For this purpose we will create special flight mode that will be activated when momentary switch SH is pressed.
 
:*IDLEUP3 will be used for the Rescue/Stabilisation modes. For this purpose we will create special flight mode that will be activated when momentary switch SH is pressed.
 
::Configure SH switch for IDLEUP3 with following ON/OFF:
 
::Configure SH switch for IDLEUP3 with following ON/OFF:
Line 39: Line 51:
 
:::ON
 
:::ON
  
 +
<!--T:13-->
 
:* Hold can be configured for SF switch with ON/OFF values:
 
:* Hold can be configured for SF switch with ON/OFF values:
 
:::OFF
 
:::OFF
 
:::ON</translate>
 
:::ON</translate>
  
<translate>Final CONDITION screen after the settings:</translate>
+
<translate><!--T:14-->
 +
Final CONDITION screen after the settings:</translate>
  
 
::[[File:F2.png]]
 
::[[File:F2.png]]
  
  
<translate>Check priorities for correct behavior – Hold has the highest priority.</translate>
+
<translate><!--T:15-->
 +
Check priorities for correct behavior – Hold has the highest priority.</translate>
  
{{Quote| '''<translate>Remember to set Throttle and Pitch Curves for NORMAL, IDLEUP1, IDLEUP2 and IDLEUP3 modes.</translate>'''
+
{{Quote| '''<translate><!--T:16-->
 +
Remember to set Throttle and Pitch Curves for NORMAL, IDLEUP1, IDLEUP2 and IDLEUP3 modes.</translate>'''
 
}}
 
}}
  
<translate>For IDLEUP3 configure higher RPM if you wish to use the rescue mode, because after activation, throttle curve will be changed too.</translate>
+
<translate><!--T:17-->
 +
For IDLEUP3 configure higher RPM if you wish to use the rescue mode, because after activation, throttle curve will be changed too.</translate>
  
 
== Gyro Gain setup ==
 
== Gyro Gain setup ==
  
'''<translate>Go to MDL  →  GYRO</translate>'''
+
'''<translate><!--T:18-->
 +
Go to MDL  →  GYRO</translate>'''
  
<translate>Gyro switching has to be performed through configured flight modes – separate gyro gain for each mode. Select COND type instead of SW in the menu.</translate>
+
<translate><!--T:19-->
 +
Gyro switching has to be performed through configured flight modes – separate gyro gain for each mode. Select COND type instead of SW in the menu.</translate>
  
 
::[[File:F3.png]]
 
::[[File:F3.png]]
  
  
:a) <translate>Select HOLD, then set TYPE GY  AVCS with RATE 60% for the beginning. That mean that Gyro Gain will be +60% when Hold is active. AVCS mode is Head Lock gyro mode for Spirit</translate>
+
:a) <translate><!--T:20-->
 +
Select HOLD, then set TYPE GY  AVCS with RATE 60% for the beginning. That mean that Gyro Gain will be +60% when Hold is active. AVCS mode is Head Lock gyro mode for Spirit</translate>
  
:b) <translate>For NORMAL, IDLEUP1 and IDLEUP2, set TYPE GY  AVCS with RATE 60% for the beginning. That mean that Gyro Gain will be +60% when these flight modes are active.</translate>
+
:b) <translate><!--T:21-->
 +
For NORMAL, IDLEUP1 and IDLEUP2, set TYPE GY  AVCS with RATE 60% for the beginning. That mean that Gyro Gain will be +60% when these flight modes are active.</translate>
  
:c) <translate>For IDLEUP3, set TYPE GY  NORMAL with RATE 60% for the beginning. That mean that Gyro Gain will be ­60% when SH is active. So this will activate Normal (Rate) Gyro mode with default settings in the unit. If Stabi/Function is not Disabled, then special mode will be activated with Head Lock Gyro mode, while Gyro Gain can be still configured.</translate>
+
:c) <translate><!--T:22-->
 +
For IDLEUP3, set TYPE GY  NORMAL with RATE 60% for the beginning. That mean that Gyro Gain will be ­60% when SH is active. So this will activate Normal (Rate) Gyro mode with default settings in the unit. If Stabi/Function is not Disabled, then special mode will be activated with Head Lock Gyro mode, while Gyro Gain can be still configured.</translate>
  
:d) <translate>Make sure that you will configure Gyro Gain in this menu for each Flight mode according to your RPM.</translate>
+
:d) <translate><!--T:23-->
 +
Make sure that you will configure Gyro Gain in this menu for each Flight mode according to your RPM.</translate>
  
== <translate>Bank Switching setup</translate> ==
+
== <translate><!--T:24-->
 +
Bank Switching setup</translate> ==
  
'''<translate>Go to LNK  →  FUNCTION</translate>'''
+
'''<translate><!--T:25-->
 +
Go to LNK  →  FUNCTION</translate>'''
  
<translate>Set channel 7 AUX1 to SG switch.</translate>
+
<translate><!--T:26-->
 +
Set channel 7 AUX1 to SG switch.</translate>
  
 
::[[File:F4.png]]
 
::[[File:F4.png]]
  
  
<translate>:In the settings of the unit go to General/Channels and assign Bank function to Channel 7.
+
<translate><!--T:27-->
 +
:In the settings of the unit go to General/Channels and assign Bank function to Channel 7.
 
:Bank switching will be performed with SG tri­state switch.
 
:Bank switching will be performed with SG tri­state switch.
  
 +
<!--T:28-->
 
::For Bank 0 you can configure for example Rescue (acro).
 
::For Bank 0 you can configure for example Rescue (acro).
 
::For Bank 1 you can configure Stabilisation mode.
 
::For Bank 1 you can configure Stabilisation mode.

Revision as of 10:10, 17 October 2018

Other languages:
čeština • ‎Deutsch • ‎English • ‎magyar • ‎italiano • ‎русский
Setup guide
for
F1.jpg
T8FG or compatible


✔Flight Modes
✔Gyro Gains
✔Normal (Rate) mode
✔Rescue and Stabiilsation
✔Bank Switching

1 Flight Mode setup

Go to MDL → CONDITION

Set the Flight mode switch SE for IDLEUP1 and IDLEUP2.

  • Make sure that ON/OFF for IDLEUP1 is configured in the following way:
OFF
ON
OFF
  • For IDLEUP2 it should be as following:
OFF
OFF
ON
  • IDLEUP3 will be used for the Rescue/Stabilisation modes. For this purpose we will create special flight mode that will be activated when momentary switch SH is pressed.
Configure SH switch for IDLEUP3 with following ON/OFF:
OFF
ON
  • Hold can be configured for SF switch with ON/OFF values:
OFF
ON

Final CONDITION screen after the settings:

F2.png


Check priorities for correct behavior – Hold has the highest priority.

Warning.png Remember to set Throttle and Pitch Curves for NORMAL, IDLEUP1, IDLEUP2 and IDLEUP3 modes.

For IDLEUP3 configure higher RPM if you wish to use the rescue mode, because after activation, throttle curve will be changed too.

2 Gyro Gain setup

Go to MDL → GYRO

Gyro switching has to be performed through configured flight modes – separate gyro gain for each mode. Select COND type instead of SW in the menu.

F3.png


a) Select HOLD, then set TYPE GY AVCS with RATE 60% for the beginning. That mean that Gyro Gain will be +60% when Hold is active. AVCS mode is Head Lock gyro mode for Spirit
b) For NORMAL, IDLEUP1 and IDLEUP2, set TYPE GY AVCS with RATE 60% for the beginning. That mean that Gyro Gain will be +60% when these flight modes are active.
c) For IDLEUP3, set TYPE GY NORMAL with RATE 60% for the beginning. That mean that Gyro Gain will be ­60% when SH is active. So this will activate Normal (Rate) Gyro mode with default settings in the unit. If Stabi/Function is not Disabled, then special mode will be activated with Head Lock Gyro mode, while Gyro Gain can be still configured.
d) Make sure that you will configure Gyro Gain in this menu for each Flight mode according to your RPM.

3 Bank Switching setup

Go to LNK → FUNCTION

Set channel 7 AUX1 to SG switch.

F4.png


In the settings of the unit go to General/Channels and assign Bank function to Channel 7.
Bank switching will be performed with SG tri­state switch.
For Bank 0 you can configure for example Rescue (acro).
For Bank 1 you can configure Stabilisation mode.
For Bank 2 you can set Disabled so Normal/Rate Gyro mode can be activated.