GeoLink Hibajelzések

From Spirit System Manual
Jump to: navigation, search
This page is a translated version of the page GeoLink Troubleshooting and the translation is 84% complete.

Other languages:
čeština • ‎Deutsch • ‎English • ‎español • ‎français • ‎magyar • ‎italiano • ‎русский

1 Pontosság

Ha egy GeoLink szolgáltatás pontosságával kapcsolatos probléma felmerül, olvassa el az alábbi fejezetet.

1.1 Sodródás

Ha a modell Pozíció tartás, Hazatérés vagy Geo kerítés módban sodródik, ellenőrizze az alábbiakat:

  • A GeoLink iránytű kalibrálása pontosan megtörtént.
  • Az olyan Stabi mód mint a Normál Stabi, Acro Stabi, Koaxiálisban még hosszú repülési idő után sem sodródhat.

1.1.1 Helytelen iránytű kalibrálás

A helytelen iránytű kalibrálás legkönnyebben a GeoLink Pozíció tartás funkcióval ellenőrizhető. Javasoljuk, hogy a funkciót biztonságos magasságban használja, majd figyelje meg a modell viselkedését.

Ha a modell köröket kezd leírni, akkor az Iránytű kalibrálása rossz. Ha még a kalibrálás a repülőtéren nem segít, a probléma alternatív módon megoldható az Iránytű Irányának Javítása paraméter beállításával.

A modellnek mozdulatlanul kell pozícióban maradnia csűrő / magassági mozgása nélkül, ha minden rendben van.

Ha a modell 5 méternél távolabb repül, azonnal kapcsolja ki a funkciót, és szálljon le. Folytassa a következő alfejezet szerinti ellenőrzést.

1.1.2 Stabilizációs sodródás

Kérjük, ellenőrizze, hogy a stabilizálás pontosan működik-e a GeoLink funkcióinak használata előtt. Ez nagyon fontos, mivel a GeoLink a stabilizációs szolgáltatáson alapul. Javasoljuk a koaxiális mód beállítását, miközben a GeoLink támogatás letiltható a teszteléshez.

The most common reason for drifting is incorrect mechanical setup - mainly servos are not centered properly. There is very simple test to check if your setup is correct:

  1. Enable Servos / Subtrim (tuning)
  2. At this point all servo arms must be in the center of their travel range. As close as possible - any visible deflection is not correct.
  3. At the same time swashplate must be perfectly level - you can check it really precisely only with Cyclic Leveler tool.
  4. At the same time there must be 0° between main blades. You can fold ends of the main blades so they are near each other. They must be at the same height wherever you will rotate with main shaft.
  5. Only after checking that all 3 are correct, verify that Geometry 6° parameter is configured precisely.

Other reasons for imprecision are ESC fan (mainly from HobbyWing ESCs) or extremely high vibration level.

It is possible to setup the model and get it into a flying condition with relatively good results even with base settings all wrong. This mean that in a certain combination of wrong Mounting Position, Swashplate type, Servo reversing in the Spirit unit and Channel reversing in the radio, it is possible to make model to fly. But all Stabilisation and Rescue modes, including GeoLink features will work completely wrong. The easiest way to check if your base settings is in the Diagnostic tab. Make sure that all base channels are moving in the same direction as actual movement of the radio sticks. If they are moving all in a proper direction, your base settings are very likely correct.

Repülhet koaxiális móddal, lehetőleg hosszabb ideig vagy legalább a repülés vége közelében. Figyelje meg, hogy a modell nem dől-e el valamelyik oldalra. Vagy azt, hogy botokkal kell-e tartani a helyben maradáshoz?

Ha igen, akkor meg kell oldani a problémát. A következő oldal szerint javítható: Pontatlan Mentés vagy Stabilizálás Beállítások a legjobb teljesítményért fejezetben.

A GeoLink funkcióinak pontos működéséhez a legjobb megoldás a Stabi Correction ON. Felhívjuk figyelmét, hogy ez a funkció nem használható minden modellnél, lásd a fenti oldalt.

1.2 Vertical pumping

In some cases model could jump up and down having jerky and imprecse altitude hold. This is mostly result of imprecise servo settings.

Please do the following checking:

  1. Enable Servos / Subtrim (tuning)
  2. At this point all servo arms must be in the center of their travel range. As close as possible - any visible deflection is not correct.
  3. At the same time swashplate must be perfectly level - you can check it really precisely only with Cyclic Leveler tool.
  4. At the same time there must be 0° between main blades. You can fold ends of the main blades so they are near each other. They must be at the same height wherever you will rotate with main shaft.
  5. Only after checking that all 3 are correct, verify that Geometry 6° parameter is configured precisely.

For some models it is needed to decrease Vertical Correction Gain if model is doing visible corrections. You can start with the lowest number and increase it by 10 points in that case.

2 Meghibásodások

Probléma esetén a GeoLink a LED villogásával értesíti a pilótát. A LED ismétlődő villogása minden hibát kijelez. Törések után a GeoLink javítását is el kell végezni, ha szükséges.

A LED villogása a bekapcsolás után azonnal megjelenhet. A felvillanások száma mutatja meg a fennálló problémát.

2.1 1 x-s felvillanás

A GeoLink tárolt hardver adatai elvesztek. Lépjen kapcsolatba a Spirit System gyártójával.

2.2 2 x-s felvillanások

A nyomásérzékelő nem működik megfelelően. Általában ez a probléma akkor jelentkezik, ha a GeoLink-et hosszabb ideig üzemeltetik rendkívül magas páratartalom mellett. Néhány órán keresztül tárolja a GeoLink-et alacsony páratartalmú környezetben, amíg a belső kondenzátum elpárolog. Ha ez nem segít, lépjen kapcsolatba a Spirit System gyártójával.

2.3 3 x-s felvillanások

Gyro, vagy/és a gyorsulásmérő szenzorok nem működnek megfelelően. Lépjen kapcsolatba a Spirit System gyártójával.

2.4 4 x felvillanás

Iránytű-érzékelő nem működik megfelelően. Lépjen kapcsolatba a Spirit System gyártójával.

2.5 Folyamatos felvillanások

This might happen rather in-flight and could signalize unexpected failure. Most probable reason is shock by high electrostatic discharge. This will result in the GeoLink connection is broken event and loss of GeoLink functionality from the moment it will occur. Please make sure that there are no excess electrostatic discharges - check ground continuity between motor and tail boom. You can also try to turn off GeoLink logging feature.

If you can't resolve this problem, we also recommend to Clear flight logs.

we recommend also to turn off GeoLink Logging feature first. GeoLink will not access to the FLASH memory and will be more immune to the static discharges.

Updating to the latest Spirit and GeoLink firmware is always recommended as precaution to any problem.

3 Egyéb értesítések

Abban az esetben, ha a GeoLink villog, és a pilóta nem tudja elérni azt a Spirit Settings segítségével, ezt az okozhatja, hogy:

3.1 Kalibrációs folyamat

Ha a GeoLink bekapcsolása után 3 gyors felvillanás sorozatokat lát (gyors 3 villanás többször), akkor a modul az úgynevezett Kalibrációs folyamatban van. Ezt a folyamatot a pilóta aktiválta a Spirit Settings szoftver segítségével, és azt az utasításoknak megfelelően még nem fejezte be. leírás. A GeoLink ennek befejezéséig nem lesz működőképes. A Spirit Settings-ben a Nem Csatlakoztatott/Not Connected üzenet látható, amíg a kalibrálás be nem fejeződik!