Устранение неполадок Geolink

From Spirit System Manual
Jump to: navigation, search
This page is a translated version of the page GeoLink Troubleshooting and the translation is 63% complete.

Other languages:
čeština • ‎Deutsch • ‎English • ‎español • ‎français • ‎magyar • ‎italiano • ‎русский

1 Точность

Если вы с неточной работой GeoLink, пожалуйста прочтите этот раздел.

1.1 Дрейф

Если модель дрейфует при активном режиме Удержине Позиции, Возврат Домой или Гео-ограждение, необходимо убедиться что:

  • Калибровка компаса GeoLink выполенна корректно.
  • Режимы стабилизации такие как Стабилизация (в нормале), Стабилизация (Акро), Кооксиальнай не приводят к дрейфу модели даже после продолжительного полета.

1.1.1 Неккоректная калибровка компаса

Incorrect Calibration can be distinguished with GeoLink Position Hold in the easiest way. We recommend to engage the feature in a safe altitude and then observe behavior of the model.

If model will start to make a circles then Compass Calibration is wrong. If even Calibration at the flying field will not help, the problem can be alternatively fixed by adjusting Compass Heading Correction parameter.

The model must stay stationary with no aileron/elevator movement when everything is correct.

If model will fly away more than 5 meters immediately disengage the feature and land. Proceed according following subsection.

1.1.2 Stabilisation drift

Please make sure that Stabilisation is working precisely prior usage of a GeoLink features. This is very important as GeoLink is based on the Stabilisation feature. We recommend to set Coaxial mode while GeoLink support can be disabled for testing.

The most common reason for drifting is incorrect mechanical setup - mainly servos are not centered properly. There is very simple test to check if your setup is correct:

  1. Enable Servos / Subtrim (tuning)
  2. At this point all servo arms must be in the center of their travel range. As close as possible - any visible deflection is not correct.
  3. At the same time swashplate must be perfectly level - you can check it really precisely only with Cyclic Leveler tool.
  4. At the same time there must be 0° between main blades. You can fold ends of the main blades so they are near each other. They must be at the same height wherever you will rotate with main shaft.
  5. Only after checking that all 3 are correct, verify that Geometry 6° parameter is configured precisely.

Other reasons for imprecision are ESC fan (mainly from HobbyWing ESCs) or extremely high vibration level.

It is possible to setup the model and get it into a flying condition with relatively good results even with base settings all wrong. This mean that in a certain combination of wrong Mounting Position, Swashplate type, Servo reversing in the Spirit unit and Channel reversing in the radio, it is possible to make model to fly. But all Stabilisation and Rescue modes, including GeoLink features will work completely wrong. The easiest way to check if your base settings is in the Diagnostic tab. Make sure that all base channels are moving in the same direction as actual movement of the radio sticks. If they are moving all in a proper direction, your base settings are very likely correct.

You can fly with Coaxial mode, preferably for a longer time or at least near the end of the flight. Observe if model will not tilt to some side. Or that it is required to hold a sticks in order to stay stationary.

If yes, it is necessary to fix the problem. It can be fixed according following page: Imprecise Rescue or Stabilisation - Settings for the best performance section.

For GeoLink features to operate the most precisely Stabi Correction ON is the best option. Please note it is not possible to utilize this feature with all models - see the page above.

1.2 Vertical pumping

In some cases model could jump up and down having jerky and imprecse altitude hold. This is mostly result of imprecise servo settings.

Please do the following checking:

  1. Enable Servos / Subtrim (tuning)
  2. At this point all servo arms must be in the center of their travel range. As close as possible - any visible deflection is not correct.
  3. At the same time swashplate must be perfectly level - you can check it really precisely only with Cyclic Leveler tool.
  4. At the same time there must be 0° between main blades. You can fold ends of the main blades so they are near each other. They must be at the same height wherever you will rotate with main shaft.
  5. Only after checking that all 3 are correct, verify that Geometry 6° parameter is configured precisely.

For some models it is needed to decrease Vertical Correction Gain if model is doing visible corrections. You can start with the lowest number and increase it by 10 points in that case.

2 Неисправности

В случае возникновения проблем, GeoLink сигнализирует встроенным светодиодом. Любой сбой индицируется периодически повторяющимися вспышками. Если было падение модели, то неполадка может потребовать ремонта модуля.

Вспышки светодиода могут появиться сразу после включения питания. По количеству вспышек вы можете определить, в чем проблема.

2.1 Однократное мигание

Аппаратные данные в GeoLink были потеряны. Необходимо связаться с поддержкой.

2.2 Двукратное мигание

Датчик давления работает неправильно. Обычно эта проблема возникает, когда GeoLink эксплуатируется в течение длительного времени в условиях чрезвычайно высокой влажности. Подержите GeoLink в условиях низкой влажности в течение нескольких часов, пока испарится внутренний конденсат. Если это не поможет, обратитесь в службу поддержки.

2.3 Трехкратное мигание

Датчики гироскопа и акселерометра работают неправильно. Необходимо связаться с поддержкой.

2.4 Четырехкратное мигание

Компас работает неправильно. Необходимо связаться с поддержкой.

2.5 Постоянное мигание

This might happen rather in-flight and could signalize unexpected failure. Most probable reason is shock by high electrostatic discharge. This will result in the GeoLink connection is broken event and loss of GeoLink functionality from the moment it will occur. Please make sure that there are no excess electrostatic discharges - check ground continuity between motor and tail boom. You can also try to turn off GeoLink logging feature.

If you can't resolve this problem, we also recommend to Clear flight logs.

we recommend also to turn off GeoLink Logging feature first. GeoLink will not access to the FLASH memory and will be more immune to the static discharges.

Updating to the latest Spirit and GeoLink firmware is always recommended as precaution to any problem.

3 Другие уведомления

В случае, если GeoLink мигает и не подключается к программе настройки, причиной может быть следующее.

3.1 Процесс калибровки

Если после включения GeoLink вы видете 3 серии быстрых миганий (последовательные беспорядочные вспышки), то модуль находится в режиме калибровки. Этот процесс мог быть инициирован в программе настройки и должен быть завершен в соответствии с инструкциями. До его завершения GeoLink будет неработоспособным. Программа настройки будет выводить "Не подключено" пока калибровка не будет завершена.