Difference between revisions of "Kontronik Telemetry/en"

From Spirit System Manual
Jump to: navigation, search
(Updating to match new version of source page)
(Importing a new version from external source)
 
(One intermediate revision by the same user not shown)
Line 3: Line 3:
 
Kontronik KOSMIK and JIVE PRO ESC has telemetry feature built-in in dedicated telemetry port. This allows telemetry data transmission to the unit.
 
Kontronik KOSMIK and JIVE PRO ESC has telemetry feature built-in in dedicated telemetry port. This allows telemetry data transmission to the unit.
  
{{Quote|'''This telemetry is available only for EX Bus connection with the Spirit firmware v2.4. In the future versions should work with other too.'''}}
+
{{Quote|'''This telemetry is available only for Jeti integration (Jeti EX Bus), Spektrum integration and Futaba with the Spirit firmware v2.4+. In the future versions should work with other too.'''}}
 
<p></p>
 
<p></p>
 
== Telemetry Cable ==
 
== Telemetry Cable ==
Line 44: Line 44:
  
 
How to display the data is described in the integration guide:
 
How to display the data is described in the integration guide:
*[[Jeti_Integration#Telemetry_data|JETI Duplex]]
+
*[[Jeti_Integration#Telemetry_data|Jeti Integration]]
 +
*[[Spektrum_Integration|Spektrum Integration]]
 +
*[[Futaba Telemetry|Futaba Telemetry]]
  
 
== Supported models ==
 
== Supported models ==

Latest revision as of 08:48, 27 October 2017

Other languages:
čeština • ‎Deutsch • ‎English • ‎español • ‎français • ‎magyar • ‎italiano • ‎русский

Kontronik KOSMIK and JIVE PRO ESC has telemetry feature built-in in dedicated telemetry port. This allows telemetry data transmission to the unit.

Warning.png This telemetry is available only for Jeti integration (Jeti EX Bus), Spektrum integration and Futaba with the Spirit firmware v2.4+. In the future versions should work with other too.

1 Telemetry Cable

To allow the telemetry data transmission the Telem KONTRONIK cable is required. This cable is available in our Eshop.

Telemkontronik.png

2 Spirit Settings

First from all, power up the ESC and start the Spirit Settings as usually.

2.1 Telemetry activation

Set the ESC Telemetry in the Spirit Settings software.

Go to the Advanced/Telemetry settings and set the Kontronik KOSMIK & JIVE PRO option.

Esc-telem-kontronik.png

Then close the window and save the settings (CTRL+S). Now disconnect the battery.

3 Interfacing

At this step, connect the Telemetry cable according the following photo.

Unit-telemkontronik.jpg

Info.png In this connection SYS port is used. Thus usage of this port for other purposes is limited when the Kontronik telemetry is enabled. Jeti Integration is still available for full configuration of the unit. If you need to use Spirit Settings software, you can deactivate temporarily ESC Telemetry by not turning transmitter on. At this moment normal connection for the USB interface or Wireless connection is established.
ELE pin is utilized for communication purpose of the telemetry interface.


Esc-kontronik.jpg

4 Displaying telemetry data

When previous steps were finished, you are ready to power up the battery.

After initialization you can display all telemetry data directly in your radio from now.

How to display the data is described in the integration guide:

5 Supported models

Model

Battery Voltage

Battery Current

BEC Voltage

Consumed Capacity

ESC Temperature

RPM

JIVE PRO 80+ HV
JIVE PRO 120+ HV
KOSMIK 160 HV
COOL KOSMIK 160 HV
KOSMIK 200 HV
COOL KOSMIK 200+ HV
COOL KOSMIK 200 HV GOLD