Difference between revisions of "SPM4649T/ru"

From Spirit System Manual
Jump to: navigation, search
(Created page with "SPM4649T это приемник с поддержкой телеметрии, который позволяет передавать одновременно значения...")
(Created page with "Используя '''Кабель интеграции Jeti''' вам не потребуется никаких дополнительных изменений в прием...")
Line 1: Line 1:
 
SPM4649T это приемник с поддержкой телеметрии, который позволяет передавать одновременно значения каналов и данные телеметрии. Это значит, что вам не потребуется подключат дополнительные кабели.
 
SPM4649T это приемник с поддержкой телеметрии, который позволяет передавать одновременно значения каналов и данные телеметрии. Это значит, что вам не потребуется подключат дополнительные кабели.
  
By using the '''Jeti integration cable''' you will not need any additional modification to the receiver. In case you do not have this cable, you can make one easily with a needle and a spare servo plug.
+
Используя '''Кабель интеграции Jeti''' вам не потребуется никаких дополнительных изменений в приемнике. Если у вас нет кабеля, его не сложно сделать самостоятельно используя дополнительный серворазъем.
  
 
[[File:Jeti-cable.jpg]]
 
[[File:Jeti-cable.jpg]]

Revision as of 07:33, 3 February 2020

SPM4649T это приемник с поддержкой телеметрии, который позволяет передавать одновременно значения каналов и данные телеметрии. Это значит, что вам не потребуется подключат дополнительные кабели.

Используя Кабель интеграции Jeti вам не потребуется никаких дополнительных изменений в приемнике. Если у вас нет кабеля, его не сложно сделать самостоятельно используя дополнительный серворазъем.

Jeti-cable.jpg

Info.png In case that your SPM4649T receiver is not bound yet, you can do so by a Bind plug. Connect the Bind plug to the servo socket. Then power up the receiver (you can use BEC power supply and/or free port in the unit such as CH0 or AUX2). Optional satellites can be bound normally as described in the Manual.


SPM4649T receiver Jeti integraction cable must be connected to the Servo socket. This socket is used also for Binding.
Spirit unit Other end of the Jeti integration cable should be connected so that Orange wire is in the AIL pin. Powering plug with Red and Brown wires in the RUD port. (see the photo)

SPM4649T receiver Spirit Pro unit


1 Spektrum satellites (optional)

To improve receiving capabilities you can connect additional Spektrum satellites. So the combination can be following:

  • Spirit 2 - 1x SPM4649T + 0-2x Spektrum satellites
  • Spirit Pro - 1x SPM4649T + 0-2x Spektrum satellites
  • Spirit - 1x SPM4649T + 0-1x Spektrum satellites
  • µSpirit - 1x SPM4649T + 0-1x Spektrum satellites

Info.png In case that the ESC telemetry is used, the primary satellite can't be connected. For the Castle Creations and Kontronik Kosmik/Jive Pro ESC telemetry primary satellite can be still used.

2 Spirit Settings

Now you are ready to power up the unit. If your Power supply is not connected yet, we recommend to connect it to the AUX1, AUX2 and/or CH0 port. Before you can utilize the Spektrum integration connection, it is important to set the Spektrum DSM2/X receiver type in the General tab of the software. Please start the Spirit Settings and change the receiver type as displayed on the photo. Then save the settings (e.g. by CTRL+S) or the Backup tab/Unit - Save and restart the unit.

Spektrum-settings.png

3 Radio Integration

If you want to use Integration and Telemetry features please continue with Spektrum Integration page.