Difference between revisions of "Spektrum Integration"

From Spirit System Manual
Jump to: navigation, search
Line 68: Line 68:
 
* 1: ESC  
 
* 1: ESC  
 
* 2: Text Gen
 
* 2: Text Gen
 +
 +
When adding ''Text Gen'' make sure that '''Display''' option is configured to '''Act''' or '''Roller''' ''(depending on radio)''.
  
 
At this point your transmitter is ready. You can return to the main screen.
 
At this point your transmitter is ready. You can return to the main screen.

Revision as of 19:56, 11 August 2017

Other languages:
čeština • ‎Deutsch • ‎English • ‎español • ‎français • ‎magyar • ‎italiano • ‎русский • ‎中文(繁體)‎

Spektrum-display.png


From version 2.4.3 you can use the Spektrum integration!

This mean you can fully configure Spirit units with Spektrum transmitters in real-time without need of a computer.

1 Requirements

To make it work you will need:

  • Spektrum transmitter: DX6e, DX6 Gen 2, DX6 Gen 3, DX7 Gen 2, DX8 Gen 2, DX9, DX10T, DX18 Gen 1, DX18 Gen 2, DX18T, DX18QQ or DX20
  • Serial Telemetry receiver: SPM4649T.
  • Jeti Integration cable available in our stores (or own modification of the wires).
  • Spirit firmware: 2.4.3 (with the new Bootloader flashed - see the Troubleshooting section)

Jeti-cable.jpg

2 Wiring

The Spektrum cable is able to transfer everything including channel data and telemetry. This mean that you will not need to connect anything else except this cable.

To improve receiving capabilities you can connect additional Spektrum satellites. So the combination can be following:

  • Spirit Pro - 1x SPM4649T + 0-2x Spektrum satellites
  • Spirit - 1x SPM4649T + 0-1x Spektrum satellites
  • uSpirit - 1x SPM4649T + 0-1x Spektrum satellites

Info.png In case that the ESC telemetry is used, the primary satellite can't be connected. For the Castle Creations and Kontronik Kosmik/Jive Pro ESC telemetry primary satellite can be still used.

Jeti-wiring.jpg


  • At the receiver side (SPM4649T) the Jeti integraction cable must be connected to the Servo socket. This socket is used also for Binding.
  • Then connect the Jeti integration cable to the unit so that red and brown wires are connected to the RUD port.
  • Orange wire should be connected with the AIL pin.


In case that your SPM4649T receiver is not bound yet, you can do so by a BIND PLUG. Connect the bind plug to the socket (same that you are using for the Jeti cable). Then power up the receiver (you can use BEC power supply, free port in the unit such as CH0 or AUX2). Optional satellites can be binded normally as you are used to do.

Spektrum-connection.jpg

3 Transmitter preparation

3.1 Firmware update

Update your transmitter to the latest firmware 1.20 from the Spektrum Airware portal. In the menu SETUPS/UPDATES - FIRMWARE UPDATES you will find the firmware for download. The SAX file must be stored on the SDCARD and inserted in your transmitter. In the System Setup/Transfer SD Card you can select Firmware update as Option.

  • DX6e does not need update (version 1.00 will work).

3.2 Configuration

Power up the transmitter and in the Main menu enter the Telemetry.

Configure:

  • 1: ESC
  • 2: Text Gen

When adding Text Gen make sure that Display option is configured to Act or Roller (depending on radio).

At this point your transmitter is ready. You can return to the main screen.

4 Spirit Settings

Now you are ready to power up the unit. If your Power supply is not connected yet, we recommend to connect it to the AUX1, AUX2 and/or CH0 port. Before you can utilize the Spektrum integration connection, it is important to set the Spektrum DSM2/X receiver type in the General tab of the software. Please start the Spirit Settings and change the receiver type as displayed on the photo. Then save the settings (e.g. by CTRL+S) or the Backup tab/Unit - Save and restart the unit.

Spektrum-settings.png

5 Integration Menu

Whenever unit is initialized you are able to enter the Spektrum Integration menu or watch the telemetry data.

Start the transmitter and on the main screen use a roller - rotate to the right until you will see a Blank screen.

5.1 Entering the menu

At this point the integration menu is closed so you can't accidently configure any parameter. To open the menu, move the Rudder stick to the right and Aileron stick to the left and hold for over 2 seconds. Once the menu is opened, you will see <READY> message. Now you can release the sticks and you are ready to set all the parameters.

5.2 Closing the menu

As soon as you will want to close the Integration menu (when you will want to fly) perform the same procedure with the sticks. Move and hold the sticks (Rudder to the right and Aileron to the left) for over 2 seconds. Menu is closed successfully when <CLOSED> is displayed even if you will return the sticks back to the center. If you will not close the integration menu, it will be temporarily disabled as soon as the Throttle curve will exceed 15%. But to minimize any risk we highly recommend to close it properly.

5.3 Usage

The Menu Layout is nearly identical with the PC software to have easy navigation.

It is working in the same way as when the PC software is connected. This mean that when Spektrum Integration menu is opened, you can change even the basic parameters that could affect the helicopter significantly.

Info.png To navitate in the menu you can use Aileron and Elevator sticks.

  • Aileron Left - Back in the menu; Stop edit of a parameter' value.
  • Aileron Right - Enter a Submenu; Edit selected parameter.
  • Elevator Up - Go up in the menu or submenu; Increase value of selected parameter.
  • Elevator Down - Go down in the menu or submenu; Decrease value of selected parameter.

Warning.png Never perform the configuration when flying!

When using the Bank Switching or Real-Time tuning features the menu will take full control over it. The unit will not react to a Switch position changes. For the Bank Switching there is a parameter Bank in the main menu where you can manually change the banks.

Do not forget to use the Save Settings when you want to save a changes permanently.


Spektrum-menu1.png


Spektrum-menu2.png


6 Telemetry data

In order to display Telemetry data, move the roller while on the Main screen until you will see ESC Status.

If you can't see the ESC Status, please make sure you have performed necessary configuration.

List of available Telemetry variables:

  • RPM [Head RPM] - RPM provided by RPM sensor or ESC.
  • Volts [V] - ESC Telemetry | Main Battery voltage
  • Motor [A] - ESC Telemetry | Main Battery current
  • Throttle [%] - Throttle percentage sent to the ESC.
  • Output [%] - (Vibration level 0 - 10% is normal level)
  • FET Temp [°C] - ESC Telemetry | FET temperature
  • BEC [C] - ESC Telemetry | Main Battery consumed capacity (1234mAh = 123.4C)
  • BEC [V] - ESC Telemetry | BEC Voltage

Spektrum-telemetry.png


7 Troubleshooting

7.1 SPM4649T always in binding mode

This issue can be sorted so that you will re-flash the unit's Bootloader to the latest version. All units that were shipped with firmware older than 2.4.3 will need this.

It can be done easily so that you will perform the flashing process again (with the latest 4df file), but before clicking the Flash button, press CTRL+B keys. Once pressed, you will see Status: Bootloader Overwrite message. Then click the Flash button. The flashing will take little bit longer than usually (done in two stages).

Warning.png Update the bootloader only if you are certain, that normal firmware flashing is working correctly on your computer.