Stabi mode

From Spirit System Manual
Jump to: navigation, search
This page is a translated version of the page Stabi mode and the translation is 1% complete.

Other languages:
čeština • ‎Deutsch • ‎English • ‎español • ‎français • ‎magyar • ‎italiano • ‎русский • ‎中文(繁體)‎

In order to enable Rescue or stabilisation modes you have to set Stabi/Function to a desired option. When Disabled, no special function will be used.

Info.png It is possible to set a different functions between Banks.

From version 2.3.0 it is possible to activate the Stabi/Function in the two ways:

  • Negative Gyro Gain
  • Separate channel (NEW)

1 Negative Gyro Gain

For normal flying a positive Gyro Gain is used. To activate function which is selected in the parameter Stabi/Function it is necessary to set a negative gyro gain.

Info.png Gyro Gain is still used to set the rudder gyro gain. At the same time, positive or negative value will determine if selected function is inactive or active. So it is important to set the gyro gain properly for both normal flight and selected function. Usually same, but opposite values are fine (for example +60%/-60%)

The function is active as long as the Gyro Gain is negative. Then the normal flight is engaged again. Because unit allow to set the Gyro Gain by your transmitter or directly in the software, you have two options how to do that.

1.1 In the transmitter (common)

This is the common way how pilots are configuring the Gyro Gain. It can be easily programmed for a two-state switch. For the Rescue a momentary switch is the best. Usually you can find the configuration in the GYRO menu in your transmitter. For the beginning you can set:

  • Position 0: 50% (normal flight)
  • Position 1: -50% (selected function)

This will set a moderate Gyro Gain and allow to select which mode will be used anytime during the flight.

Do not forget to set the gains accordingly for your model. Also make sure that the Gyro Gain function is assigned in the software.

1.2 In the software

When you do not want to or can't set your Gyro Gain in the transmitter, you can do so in the software. There is only requirement to unassign the Gyro Gain function in the General/Channels window. This mean that transmitter have no control over the Gyro Gain. Instead the value is configured by the Sensor/Rudder Gain parameter.

There is disadvantage that in order to activate selected function, you have to set a negative Rudder Gain. This can't be changed during the flight normally. On the other hand, you can use a Bank Switching feature and program a different Function and Rudder Gain for each bank.

1. First step
2.Second step

1.3 Function vs Gyro

Following table is describing how Gyro Gain can activate selected Function.

Function Gyro Gain Gyro Mode Flight Mode
Disabled 0 - 100% Head-Lock -
Rescue (Normal) 0 - 100% Head-Lock -
Rescue (Acro) 0 - 100% Head-Lock -
Stabilisation (Normal) 0 - 100% Head-Lock -
Stabilisation (Acro) 0 - 100% Head-Lock -
Stabilisation (Scale) 0 - 100% Head-Lock -
Coaxial 0 - 100% Head-Lock -
Disabled -100% - 0% Normal (Rate) -
Rescue (Normal) -100% - 0% Head-Lock Rescue
Rescue (Acro) -100% - 0% Head-Lock Rescue
Stabilisation (Normal) -100% - 0% Head-Lock Stabilisation
Stabilisation (Acro) -100% - 0% Head-Lock Stabilisation
Stabilisation (Scale) -100% - 0% Normal (Rate) Stabilisation
Coaxial -100% - 0% Head-Lock Stabilisation

2 Separate channel

Function in the Stabi/Function parameter will be activated by a dedicated channel selected in the General/Channels.

Channel configuration
  1. Open the General/Channels.
  2. In the right part of the Channels window, select F: Stabi Function.
  3. Then select a channel that you can use for the activation.
  4. Assign a switch in your transmitter that will control the channel (assigned channel should react now).
Function indicator
  • 0 - function is inactive.
  • 1 - function is active.

Stabi-function.png

Info.png Gyro Gain can still change gyro mode (Head-Lock or Normal). Positive Gyro Gain value will activate Head-Lock mode always. Active Function and Gyro mode is always visible in the Diagnostic tab.

2.1 Function vs Channel

Following table is describing how selected Channel can activate the Function.

  • Flight Mode "-" mean that the function is inactive and a normal flight regime is on.
Function Channel Gyro Mode Flight Mode
Disabled -100% - 0% Head-Lock / Normal -
Rescue (Normal) -100% - 0% Head-Lock -
Rescue (Acro) -100% - 0% Head-Lock -
Stabilisation (Normal) -100% - 0% Head-Lock -
Stabilisation (Acro) -100% - 0% Head-Lock -
Stabilisation (Scale) -100% - 0% Head-Lock / Normal -
Coaxial -100% - 0% Head-Lock -
Disabled 0 - 100% Head-Lock / Normal -
Rescue (Normal) 0 - 100% Head-Lock Rescue
Rescue (Acro) 0 - 100% Head-Lock Rescue
Stabilisation (Normal) 0 - 100% Head-Lock Stabilisation
Stabilisation (Acro) 0 - 100% Head-Lock Stabilisation
Stabilisation (Scale) 0 - 100% Head-Lock / Normal Stabilisation
Coaxial 0 - 100% Head-Lock Stabilisation