Difference between revisions of "TelMe Telemetry/ru"
(Updating to match new version of source page) |
(Updating to match new version of source page) |
||
Line 1: | Line 1: | ||
<languages /> | <languages /> | ||
− | + | Kontronik ESCs are utilizing special 5-pin port connector for telemetry data transmission to the unit. | |
− | + | To allow the ESC telemetry, it is necessary to have updated ESC to at least 1.13 (JIVE PRO) and 4.14 (KOSMIK) firmware version. Older versions do not support TelMe protocol. | |
== Телеметрийный кабель == | == Телеметрийный кабель == | ||
Line 17: | Line 17: | ||
[[File:unit-telemuni.jpg|350px]] | [[File:unit-telemuni.jpg|350px]] | ||
− | 5-pin JST connector of the Telem KONTRONIK v2 cable should be connected to the ESC. In case of Kontronik KOSMIK | + | 5-pin JST connector of the Telem KONTRONIK v2 cable should be connected to the ESC. In case of Kontronik KOSMIK please use port in the middle. |
[[File:esc-kontronik.jpg|350px]] | [[File:esc-kontronik.jpg|350px]] |
Revision as of 19:13, 17 December 2018
Kontronik ESCs are utilizing special 5-pin port connector for telemetry data transmission to the unit. To allow the ESC telemetry, it is necessary to have updated ESC to at least 1.13 (JIVE PRO) and 4.14 (KOSMIK) firmware version. Older versions do not support TelMe protocol.
Contents
1 Телеметрийный кабель
Для использования телеметрии необходим кабель Telem KONTRONIK v2 который доступен в нашем магазине.
We do not recommend to make this cable at home since improper connection will cause permanent damage of the unit.
2 Подключение
Подключите телеметрийный кабель к основному порту Spektrum сателлита. В младших версиях Spirit он единственный.
5-pin JST connector of the Telem KONTRONIK v2 cable should be connected to the ESC. In case of Kontronik KOSMIK please use port in the middle.
3 Spirit Settings
Подключите аккумулятор и запустите программу настройки.
3.1 Настройка телеметрии
Последним шагом надо установить тип телеметрии в программе настройки.
Перейдите на вкладку Дополнительно / Настройки телеметрии и установите Kontronik TelMe .
Закройте окно и сохраните настройки (CTRL+S) , затем переподключите питание.
С этого момента все должно работать.
4 Отображение телеметрийных данных
Теперь вы можете отображать данные телеметрии прямо на передатчике.
Как это настроить, описано в руководствах по интеграции:
5 Поддерживаемые модели
Модель |
Напряжение силового аккумулятора |
Ток силового аккумулятора |
Напряжение BEC |
Потребленная емкость |
Температура ESC |
Обороты |
---|---|---|---|---|---|---|
KOLIBRI 140 LV | ✔ | ✔ | ✔ | ✔ | ✔ | ✔ |
JIVE PRO 80+ HV | ✔ | ✔ | ✔ | ✔ | ✔ | ✔ |
JIVE PRO 120+ HV | ✔ | ✔ | ✔ | ✔ | ✔ | ✔ |
KOSMIK 160 HV | ✔ | ✔ | ✔ | ✔ | ✔ | ✔ |
COOL KOSMIK 160 HV | ✔ | ✔ | ✔ | ✔ | ✔ | ✔ |
KOSMIK 200 HV | ✔ | ✔ | ✔ | ✔ | ✔ | ✔ |
COOL KOSMIK 200+ HV | ✔ | ✔ | ✔ | ✔ | ✔ | ✔ |
COOL KOSMIK 200 HV GOLD | ✔ | ✔ | ✔ | ✔ | ✔ | ✔ |