Difference between revisions of "Wifi-Link/ru"

From Spirit System Manual
Jump to: navigation, search
(Created page with "Настройка.")
(Created page with "Модуль Wi-Fi Link для Spirit предлагает дружелюбный интерфейс настройки для любого устройства, которо...")
Line 69: Line 69:
 
== Настройка. ==
 
== Настройка. ==
  
'''Spirit Wifi-Link''' offers you user friendly configuration from any device that support WiFi connection and web browser.
+
'''Spirit Wifi-Link''' Модуль Wi-Fi Link для Spirit предлагает дружелюбный интерфейс настройки для любого устройства, которое может соединяться по Wi-Fi и имеет веб браузер.
  
 
To open it, you can proceed in this way:
 
To open it, you can proceed in this way:

Revision as of 14:10, 15 October 2018

Other languages:
čeština • ‎Deutsch • ‎English • ‎español • ‎français • ‎magyar • ‎italiano • ‎русский
Wifi-Link
руководство
107.jpg



1 Функции

Напряжение питания 3.3V - 15V
Вес 7g
Размеры 21x32x5.5mm
Радиус действия до 50 метров
Режимы работы AP, AP+Client, Client
Стандарт ПД 802.11b/g/n
Шифрование Open, WEP, WPA, WPA2
Настройка Web Interface
Потребление 80 – 350mA

Поддерживаемые устройства:

  • Android доступно на Google Play
  • Все смартфоны,планшеты, смарт ТВ с браузером
  • PC
  • Mac


Поддерживает обновление прошивки.
Программа настройки через браузер в модуле!

2 Подключение

Wifi0.png
Пример подключения: .


Обозначения проводов
VCC Плюсовой провод питания: 3.3-15В
GND Минусовой провод
RX Передача данных, порт SYS
TX Передача данных, порт SYS


Info.png Провод TX всегда должен быть ближе к надписи SYS. Провод RX идет к центральному пину порта SYS.
VCC и GND могут быть подключены к любому порту кроме ELE/PIT/AIL и SYS. Их также можно вставить и в приемник. Если питание подается от отдельного аккумулятора, его GND также должен быть связан с “землей” модуля.

Warning.png НЕ подключайте провода передачи данных к питанию! Их подключаем только в порт SYS.

3 Настройка.

Spirit Wifi-Link Модуль Wi-Fi Link для Spirit предлагает дружелюбный интерфейс настройки для любого устройства, которое может соединяться по Wi-Fi и имеет веб браузер.

To open it, you can proceed in this way:

  1. Connect to the Wifi module.
    Default SSID (Wifi site name): Spirit Wifi-Link.
    The module is by default in the Access Point mode.
    You can connect to the AP directly in a normal way.
    After connection, your device will get IP address automaticaly.
  2. Open your web browser.
    Usually any modern web browser with JavaScript support can be used.
  3. Enter the module with this address: http://192.168.4.1
    By entering „192.168.4.1“ you will get into the configuration.Here you can change any parameter including changing SSID,password or wireless mode.

With the latest module firmware Spirit Settings is available directly from your web browser!

Wifi2.png


Info.png For beginners, we recommend default settings.

AP+Client Mode (For experienced users only)

Module is able to connect to an existing WiFi station (e.g. your home network). By entering the configuration interface, you can set the AP+Client mode. In this mode you can find your network and connect to it. In this way, module can be accessed from any device, that is connected to the same network, even via an ethernet cable.
If you are connected to an existing WiFi station, the module will receive second IP address. You can find such IP address in the configuration interface.
You can connect to the interface from the second IP address when accessing from your network. You can also access the internet or module at the same time.

Connecting to an existing network

  1. Connect to the Spirit Wifi-Link.
  2. Enter the WiFi Client section in the web interface.
  3. Click the „Switch to AP+Client mode“ (if not already).
  4. Wait a few seconds to display all available Wi-Fi networks.
  5. In the WiFi Association select Wi-Fi network you want to connect.
  6. Enter password of the Wi-Fi network (if required).
  7. Click the Connect button and wait for the success notification.
  8. Remember the address that will appear in the „WiFi address“ entry – this IP address should be used to connect the module through the network you are connected to.

4 USAGE

When Spirit unit with the module are running, you can proceed with the following steps:

Web Browser - iOS, WP, Sailfish OS, PC, Mac, ...

  1. Go to the Settings/Wi-Fi in the system, search for a new networks.
  2. Connect to the „Spirit Wifi-Link ...“ network.
  3. Enter the module with this address: http://192.168.4.1
  4. Click the Spirit Settings in the Menu of the Wifi-Link interface

The best experience with Chrome, Firefox, Safari web browsers.

Native Android app

  1. Download the latest „Spirit Settings“ app from the Google Play.
  2. Go to the Settings/Wi-Fi in the Android, search for a new networks.
  3. Connect to the „Spirit Wifi-Link ...“ network.
  4. Open the Spirit Settings app.
  5. Go to the Connection and select WIFI device.
  6. Click the Connect button and you are ready

Native PC & Mac app

  1. Download and install the Spirit Settings software from Spirit System web page. Required version is at least 2.0.2.
  2. Go to the Wi-Fi settings in the system, search for a new networks.
  3. Connect to the „Spirit Wifi-Link ...“ network.
  4. Start the Spirit Settings app in the Demo mode
  5. Press CTRL+W to open Wifi-Link window and confirm the IP.
  6. Close and start the app again – connection should work now.