GeoLink Configuration/en - Revision history

FuzzyBot: Updating to match new version of source page

2022-09-15T13:39:58Z

Updating to match new version of source page

2022-09-15T13:37:22Z

Importing a new version from external source

2022-09-06T11:21:40Z

Importing a new version from external source

2022-09-06T10:37:54Z

Importing a new version from external source

2022-09-06T09:39:25Z

Importing a new version from external source

2022-09-06T09:19:56Z

Importing a new version from external source

2022-09-06T09:19:53Z

Importing a new version from external source

2022-09-06T09:00:05Z

Importing a new version from external source

2022-09-06T08:59:16Z

Importing a new version from external source

2022-09-06T08:58:56Z

Importing a new version from external source

@@ Line 102: / Line 102: @@
 === Return to Home ===
-Whenever you will loose orientation, this function is the best option. You have to only engage the function with your transmitter and wait a moment, until the model returns to defined position.
+Whenever you will loose orientation, this function is the best option. You have to only engage the function with your transmitter and wait until the model returns to a defined position.
 Visit [[GeoLink_Return_to_Home|Return to Home page]] to see all details about the function.

@@ Line 40: / Line 40: @@
 #During following power up of the model you will immediately notice 3 series of rapid LED flashing on the GeoLink. This always signalize module is in the Calibration mode.
-#The Status LED will be indicating progress of the calibration then. Start moving with the model in all possible directions and angles to mimic a sphere. Any LED flash will indicate that a new calibration data were acquired.
+#Blue GeoLink LED will be indicating progress of the calibration. GeoLink v2 will light up also Green LED when calibration is ongoing.
-#Rotate with the module as long until you will see periodic LED flashing. At this point the calibration is finished. After following re-power the module is ready for operation.
+#Start moving with the model in all possible directions and angles to mimic a sphere. When Blue LED will flash then it will indicate a new calibration data were acquired.
 Successful calibration will end up only with periodic GeoLink LED light flashing. If you will not reach to this point then model was not rotated to all directions. During next power up new calibration will be started. This will happen for next 2 times if calibration will be not finished. If it is not finished even for the 3rd time then original calibration data will be used.

@@ Line 80: / Line 80: @@
 ==== Dedicated GeoLink channel [Recommended] ====
-Alternatively you can assign a GeoLink feature to any free channel in the General/Channels window. In the right part of the Spirit Settings software select which feature you would like to assign. (for example '''F: Return to Home'''). Then select appropriate channel which will be used for engaging.
+More strightforward way is to assign a GeoLink feature to any free channel in the General/Channels window. In the right part of the Spirit Settings software select which feature you would like to assign. (for example '''F: GeoLink Return to Home'''). Then select appropriate channel which will be used for engaging.
 You can use same channel for multiple features at the same time.

← Older revision		Revision as of 09:39, 6 September 2022
Line 69:		Line 69:
	If a feature is engaged you will see '''ACTIVE''' or in other case '''Inactive'''.		If a feature is engaged you will see '''ACTIVE''' or in other case '''Inactive'''.

−	{{Quote\|For safety reasons ~~do not engage any~~ GeoLink ~~feature~~ before ~~model is~~ in the ~~air~~ at ~~appropriate altitude~~.}}	+	{{Quote\|For safety reasons turn off all GeoLink features before lift off. Then in a safe altitude you can enable the feature carefully. All features can be instantly disengaged at any moment so you can continue in a normal flight.}}

@@ Line 78: / Line 78: @@
 We recommend to use this way only when you are out of a free channels.
-==== Dedicated GeoLink channel ====
+==== Dedicated GeoLink channel [Recommended] ====
 Alternatively you can assign a GeoLink feature to any free channel in the General/Channels window. In the right part of the Spirit Settings software select which feature you would like to assign. (for example '''F: Return to Home'''). Then select appropriate channel which will be used for engaging.

@@ Line 3: / Line 3: @@
 == GeoLink Support ==
-GeoLink is supported from firmware version 2.5. In order to utilize all the functions it is necessary to enable the support in the Spirit Settings - ''General tab'' first.
+Spirit GeoLink module is supported by all Spirit units. In order to utilize all the functions it is necessary to enable the support in the Spirit Settings - ''General tab'' first.
 After enabling, save the settings and re-power the model.

@@ Line 18: / Line 18: @@
 If your model will start to do a circles around a spot it should fly, then it is clear mark that the Compass Calibration is required.
-To verify that GeoLink is calibrated correctly for your area, please launch the ''Spirit Settings'' and open ''GeoLink settings'' window.
+To precisely verify that GeoLink is calibrated correctly for your area, please launch the ''Spirit Settings'' and open ''GeoLink settings'' window.
 At '''Info tab''' you can see current Heading value.

@@ Line 63: / Line 63: @@
 === Triggering ===
-You can verify if triggering mechanism is working correctly even before actual flight by checking the Aid tab.
+You can verify if triggering mechanism for any feature is working correctly even before actual flight by checking the Aid tab.
 If a feature is engaged you will see '''ACTIVE''' or in other case '''Inactive'''.