GeoLink Mounting/en - Revision history

FuzzyBot: Importing a new version from external source

2022-09-06T07:35:49Z

Importing a new version from external source

2022-01-16T00:06:47Z

Importing a new version from external source

2022-01-16T00:06:38Z

Importing a new version from external source

2022-01-15T23:32:28Z

Importing a new version from external source

2022-01-15T23:29:09Z

Importing a new version from external source

2022-01-15T23:13:36Z

Importing a new version from external source

2022-01-15T23:08:18Z

Importing a new version from external source

2022-01-15T23:08:18Z

Importing a new version from external source

2022-01-15T23:08:12Z

Importing a new version from external source

2022-01-15T22:35:33Z

Importing a new version from external source

@@ Line 72: / Line 72: @@
 {{Quote|'''Never pull the module in any way when mounted with double sided tape! This could bent or crack the plastic enclosure.'''}}
 <br/>
 === Mounting examples ===

@@ Line 61: / Line 61: @@
 <br/>
-{{Quote|'''The tape will shortly adhere on the surface tightly and can't be reused anymore.'''}}
+{{Quote|'''The tape will shortly adhere at the surface tightly and can't be reused anymore.'''}}
 <br/>

@@ Line 96: / Line 96: @@
 |-
 | style="width: 55%;"|'''μSpirit'''
-|'''SAT''' - Satellite port
+|'''Primary''' satellite port (SAT)
 |-
 | style="width: 55%;"|'''Spirit'''

@@ Line 5: / Line 5: @@
 Please take special care in order to perform the following steps thoroughly.
-== Mounting on your helicopter ==
+== Mounting at the helicopter ==
 As of now, module must be mounted always horizontally so that GeoLink logo is at the top.

@@ Line 142: / Line 142: @@
 #Open ''General tab - GeoLink module'' settings.
 #Move to the ''Module tab'' there.
-#Place GeoLink at a flat, aligned horizontal surface anywhere on your model in order to get a precise reference. (for example the Spirit unit)
+#Place GeoLink at a flat, aligned horizontal surface anywhere at your model in order to get a precise reference. (for example the Spirit unit)
 #Click '''Set as zero (temporarily)''' button to reset angle of built-in protractor.
 #Move GeoLink to a desired mounting position.

@@ Line 23: / Line 23: @@
 * It is at least 30cm far from any magnet (especially canopy magnetic mounts)
 * It has clear sky visibility
-* It is perfectly horizontally aligned
+* Is horizontally aligned as close as possible
 Choose a position which is not too far, so that provided cable is long enough. Placing module too far at the boom could lead to bad Center of Gravity of the model.

← Older revision	Revision as of 23:08, 15 January 2022
(No difference)

@@ Line 35: / Line 35: @@
 Optionally you can use a third party mounting support designed for GPS modules.
 <br/>
-{{Quote|'''Never mount GeoLink directly on a thick metallic parts, near a motor or any servo.'''}}
+{{Quote|'''Never mount GeoLink directly at a thick metallic parts, near a motor or any servo.'''}}
 <p></p>
 {{Quote|'''Do not cover GeoLink connector with any tape, glue or paint. Opening above the connector is used to determine ambient pressure and altitude.'''}}

@@ Line 25: / Line 25: @@
 * It is perfectly horizontally aligned
-Choose a position which is not too far, so that provided cable is long enough. Placing module too far on the boom could lead to bad Center of Gravity of the model.
+Choose a position which is not too far, so that provided cable is long enough. Placing module too far at the boom could lead to bad Center of Gravity of the model.
 === How to mount ===

@@ Line 48: / Line 48: @@
 === Mounting with provided tape ===
-'''1. Take the first piece of tape and glue it approximately in the middle.'''
+'''1. Take the first piece of tape and put it approximately in the middle.'''
 [[File:geolink-mounting-1.jpg|500px|center]]