GeoLink Position Hold - Revision history

Admin: Marked this version for translation

2022-09-15T13:51:58Z

Marked this version for translation

Admin at 13:51, 15 September 2022

2022-09-15T13:51:52Z

Admin at 08:36, 6 September 2022

2022-09-06T08:36:01Z

Admin: Created page with "== Position Hold == === How it works === The model is flying similarly as with Coaxial mode. Pilot can c..."

2022-09-06T08:27:52Z

Created page with "== <translate>Position Hold</translate> == === <translate>How it works</translate> === <translate>The model is flying similarly as with Coaxial mode. Pilot can c..."

New page

== <translate>Position Hold</translate> ==

=== <translate>How it works</translate> ===

<translate>The model is flying similarly as with [[Coaxial|Coaxial mode]]. Pilot can control the model fully but all movement speed is controlled so it can't fly too fast. Rather you can fly very safely as with a Coaxial model and without undesired drifting caused by wind.
Always when sticks are released the model will stop at that point and will maintain it until other steering command is given.
The model can't be flipped over.
This feature can work also upside down in the same way.

Rudder control is identical as with a normal flying mode.</translate>

<translate>To enable this feature it is required to tick the CheckBox in the GeoLink window/Aid tab.</translate>

[[File:geolink-hold.png|center|thumb]]

=== <translate>
Usage</translate> ===

<translate>
The feature can be engaged at any given time by a command from your radio. It is important to decide in which way the feature can be engaged as there are two options.


# To engage with Stabi function - in this case the feature is engaged when programmed Stabi function is engaged. This mean you do not need to assign any other switch than when used for e.g. Stabilisation mode
# To engage with assigned GeoLink channel - it is required to assign ''F: GeoLink Position Hold'' function in the ''General/Channels'' to an available channel.</translate>

@@ Line 2: / Line 2: @@
-== <translate>Position Hold</translate> ==
+== <translate><!--T:75-->
-=== <translate>How it works</translate> ===
+=== <translate><!--T:76-->
-<translate>The model is flying similarly as with [[Coaxial|Coaxial mode]]. Pilot can control the model fully but all movement speed is controlled so it can't fly too fast. Rather you can fly very safely as with a Coaxial model and without undesired drifting caused by wind.
+<translate><!--T:77-->
 Always when sticks are released the model will stop at that point and will maintain it until other steering command is given.
 The model can't be flipped over.
 This feature can work also upside down in the same way.
 Rudder control is identical as with a normal flying mode.</translate>
-<translate>To enable this feature it is required to tick the CheckBox in the GeoLink window/Aid tab.</translate>
+<translate><!--T:79-->
 [[File:geolink-hold.png|center|thumb]]
@@ Line 31: / Line 36: @@
 {|style="width: 100%;color: white;"
 |-
-| style="width: 33%;"| [[<translate>GeoLink_Configuration</translate>|&larr; <translate>Configuration</translate>]]
+| style="width: 33%;"| [[<translate><!--T:80-->
 | style="width: 33%;text-align:center;"| [[#up|&uarr;<translate><!--T:74-->
 Up</translate>&uarr;]]

← Older revision		Revision as of 13:51, 15 September 2022
Line 1:		Line 1:
		+	<languages/>
		+
		+
	== <translate>Position Hold</translate> ==		== <translate>Position Hold</translate> ==

← Older revision		Revision as of 08:36, 6 September 2022
Line 23:		Line 23:
	# To engage with Stabi function - in this case the feature is engaged when programmed Stabi function is engaged. This mean you do not need to assign any other switch than when used for e.g. Stabilisation mode		# To engage with Stabi function - in this case the feature is engaged when programmed Stabi function is engaged. This mean you do not need to assign any other switch than when used for e.g. Stabilisation mode
	# To engage with assigned GeoLink channel - it is required to assign ''F: GeoLink Position Hold'' function in the ''General/Channels'' to an available channel.</translate>		# To engage with assigned GeoLink channel - it is required to assign ''F: GeoLink Position Hold'' function in the ''General/Channels'' to an available channel.</translate>
		+
		+	<div class=noprint>
		+	----
		+	{\|style="width: 100%;color: white;"
		+	\|-
		+	\| style="width: 33%;"\| [[<translate>GeoLink_Configuration</translate>\|← <translate>Configuration</translate>]]
		+	\| style="width: 33%;text-align:center;"\| [[#up\|↑<translate><!--T:74-->
		+	Up</translate>↑]]
		+	\|}
		+	----
		+	</div>