FuzzyBot: Updating to match new version of source page

2023-12-01T10:07:29Z

Updating to match new version of source page

FuzzyBot: Importing a new version from external source

2023-11-17T09:29:57Z

Importing a new version from external source

New page

<languages />

Graupner HoTT ESC has telemetry feature built-in in the Programming port. This allows telemetry data transmission to the unit.
To allow the ESC telemetry, it is necessary to have updated ESC firmware to a more recent.

It is important to flash firmware with Sensor Emulation called '''EAM - Electric Air Module'''.

== Telemetry Cable ==
To allow the telemetry data transmission the '''Telem UNI cable''' is required. This cable is available in our [http://store.spirit-system.com/en/accessories/34-telemuni-cable.html Eshop].

[[File:telemuni.png|280px]]

{{Quote|We do not recommend to make this cable at home since improper connection will cause permanent damage of the unit.
The Red wire must be internally disconnected always!}}

== Interfacing ==

Connect the Telemetry cable to the primary Spektrum satellite port ('''SAT1''') in the unit - apply for Spirit 2, Spirit RS, Spirit Pro, Spirit GT, Spirit GTR.

Smaller Spirit units will utilize the one native Spektrum satellite port ('''SAT''') - apply for μSpirit and Spirit 1.

[[File:unit-telemuni.jpg|350px]]

Servo connector of the Telem UNI cable should be connected to the ESC - telemetry/programming port.

[[File:esc-hott.jpg|350px]]

== Spirit Settings ==

Power up the ESC and start the Spirit Settings as usually.

=== Telemetry activation ===

As the last step you have to set the ESC Telemetry in the Spirit Settings software.

Go to the '''Advanced/Telemetry settings''' and set the '''Graupner HoTT''' option.

[[File:esc-telem-hott.png|400px]]

Then close the window and save the settings ''(CTRL+S)''. Finally, reconnect battery from the ESC.

From this moment, everything should work.

== Displaying telemetry data ==

You can display telemetry data directly in your radio from now.

How to display the data is described in the integration guides:
*[[Jeti_Integration|JETI Duplex]]
*[[OpenTX_Integration|OpenTX]]
*[[EthOS|FrSky EthOS]]
*[[Hott_Integration|Graupner HoTT]]
*[[Spektrum_Integration|Spektrum Integration]]
*[[Futaba Telemetry|Futaba Telemetry]]

<p></p>

{{Quote|Please update your ESC firmware to the most recent firmware. It is important to flash firmware with Sensor Emulation called EAM - Electric Air Module.}}

<p></p>
{{Info|[[File:Info.png]] Consumed Capacity is calculated from the Current Consumption.}}

← Older revision		Revision as of 10:07, 1 December 2023
Line 60:		Line 60:
	<p></p>		<p></p>
	{{Info\|[[File:Info.png]] Consumed Capacity is calculated from the Current Consumption.}}		{{Info\|[[File:Info.png]] Consumed Capacity is calculated from the Current Consumption.}}
		+
		+	== Supported models ==
		+
		+	{\| class="servolist"
		+	!
		+	Model
		+	!
		+	Battery Voltage
		+	!
		+	Battery Current
		+	!
		+	Consumed Capacity
		+	!
		+	ESC Temperature
		+	!
		+	RPM
		+	\|-
		+	\| Graupner Cool Control +T 160HV
		+	\| style="text-align:center;" \|✔
		+	\| style="text-align:center;" \|✔
		+	\| style="text-align:center;" \|✔
		+	\| style="text-align:center;" \|✔
		+	\| style="text-align:center;" \|✔
		+	\|}
		+	<p></p>
		+	Other unlisted models that are telemetry enabled with a proper firmware should work too.

HoTT Telemetry/en - Revision history

FuzzyBot: Updating to match new version of source page

FuzzyBot: Importing a new version from external source