Imprecise Rescue/en - Revision history

FuzzyBot: Importing a new version from external source

2020-09-11T07:52:04Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2020-09-11T07:51:46Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2020-09-11T07:50:58Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2020-09-11T07:50:49Z

Importing a new version from external source

FuzzyBot: Updating to match new version of source page

2020-09-11T07:49:56Z

Updating to match new version of source page

FuzzyBot: Importing a new version from external source

2018-10-13T18:02:11Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2018-10-13T18:01:33Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2018-09-16T12:47:31Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2018-02-07T09:42:04Z

Importing a new version from external source

FuzzyBot: Updating to match new version of source page

2018-02-07T09:32:14Z

Updating to match new version of source page

@@ Line 37: / Line 37: @@
 == Rescue/Stabilisation is imprecise during flight ==
-:#Very important is to check, whether the Position and the Swashplate parameters are configured correctly. If not, these modes can't operate properly. Make sure that in the Diagnostic tab all directions correspond with real stick movement.
+*Very important is to check, whether the Position and the Swashplate parameters are configured correctly. If not, these modes can't operate properly. Make sure that in the Diagnostic tab all directions correspond with a real stick movement.
-:#Check if the unit is aligned in all 3 axes. Alignment error should be approx. in 1° range or less. You should mount the unit precisely in respect to the helicopter' frame. Use only one provided adhesive tape. The unit should not flex or move in any way - mounting should be rock solid.
+*Check if the unit is aligned in all 3 axes. Alignment error should be approx. in 1° range or less. You should mount the unit precisely in respect to the helicopter' frame. Use only one provided adhesive tape. The unit should not flex or move in any way - mounting should be rock solid.
-:#Rescue and Stabilisation can work in nearly any condition. But in case that your Vibrations are exceptionally high it can't be guaranteed. You can check vibrations with Spectral Analysis in the software, especially Y - Aileron axis, where there are mostly the highest.
+*Rescue and Stabilisation can work in nearly any condition. But in case that your Vibrations are exceptionally high it can't be guaranteed. You can check vibrations with Spectral Analysis in the software, especially Y - Aileron axis, where there are mostly the highest.
-:#Helicopter was tilted during initialization or after initialization (it was on the side or upside down for a while). If you move with helicopter after initialization, make sure that the swashplate is level and collective is going up when the rescue is engaged.
+*Helicopter is equipped with a cooling fan that is producing ultrasound frequency. Fans from HobbyWing ESCs are known for this. This has a great impact on the precision of Rescue and Stabilisation modes.
-:#Helicopter is equipped with a cooling fan that is producing ultrasound frequency. Fans from HobbyWing ESCs are known for this. This has a great impact on the precision of Rescue and Stabilisation modes.

@@ Line 35: / Line 35: @@
 Use this parameter only if default settings are not satisfying and model is in a good condition. Otherwise results can be worsened.
-:What to do if your Rescue or Stabilisation modes are not precise?
+== Rescue/Stabilisation is imprecise during flight ==
 :#Very important is to check, whether the Position and the Swashplate parameters are configured correctly. If not, these modes can't operate properly. Make sure that in the Diagnostic tab all directions correspond with real stick movement.

← Older revision		Revision as of 07:50, 11 September 2020
Line 44:		Line 44:


−	:In case that the model is tilting to the same side during activation always, then the basic servo settings are not correct.	+	:In case that the model is tilting to the same side during activation always, then the basic servo settings are likely not correct.
	:Please verify that the swashplate is perfectly leveled when ''Servos/Subtrim (tuning)'' is enabled. During setup it is necessary to use the Cyclic Leveler tool.		:Please verify that the swashplate is perfectly leveled when ''Servos/Subtrim (tuning)'' is enabled. During setup it is necessary to use the Cyclic Leveler tool.

@@ Line 3: / Line 3: @@
 <div id="up"></div>
-'''Rescue/Stabilisation is imprecise :'''
+'''What to do when Rescue/Stabilisation is imprecise?'''
 Perform Bench testing first. If it is correct, you are ready to fly.

@@ Line 4: / Line 4: @@
 '''Rescue/Stabilisation is imprecise :'''
 :What to do if your Rescue or Stabilisation modes are not precise?
@@ Line 13: / Line 43: @@
 :#Helicopter is equipped with a cooling fan that is producing ultrasound frequency. Fans from HobbyWing ESCs are known for this. This has a great impact on the precision of Rescue and Stabilisation modes.
 :In case that the model is tilting to the same side during activation always, then the basic servo settings are not correct.

← Older revision		Revision as of 18:01, 13 October 2018
Line 1:		Line 1:
	<languages/>		<languages/>
		+
	<div id="up"></div>		<div id="up"></div>

@@ Line 15: / Line 15: @@
 :In case that the model is tilting to the same side during activation always, then the basic servo settings are not correct.
 :Please verify that the swashplate is perfectly leveled when ''Servos/Subtrim (tuning)'' is enabled. During setup it is necessary to use the Cyclic Leveler tool.
 {{Info|[[File:Info.png|18px]]
@@ Line 21: / Line 22: @@
 <div class=noprint>
 ----
 {|style="width: 100%;color: white;text-align:center;"
 |[[Special:MyLanguage/#up|&uarr;Up&uarr;]]
 |}
 ----
 </div>