Jeti Integration/en - Revision history

FuzzyBot: Importing a new version from external source

2021-07-12T13:51:25Z

Importing a new version from external source

2021-07-12T13:39:26Z

Importing a new version from external source

2021-07-12T13:25:46Z

Importing a new version from external source

2021-07-12T13:19:04Z

Importing a new version from external source

2021-07-12T13:12:53Z

Importing a new version from external source

2021-07-12T13:12:36Z

Importing a new version from external source

2021-07-12T13:11:44Z

Importing a new version from external source

2021-07-12T12:51:55Z

Importing a new version from external source

2021-07-12T12:32:40Z

Importing a new version from external source

2021-07-12T12:32:15Z

Importing a new version from external source

@@ Line 58: / Line 58: @@
 == Transmitter preparation ==
-Now download the [https://spirit-system.com/dl/jeti/SPIRIT-3-3.zip Configuration file], which has BIN extension. The file name is
+Now download the [https://spirit-system.com/dl/jeti/SPIRIT-3-3.zip Configuration file], which has ZIP extension. The file archive must be extracted first (by Right click). You will obtain SPIRIT-3-3 folder.
 Content of this folder must be copied to the '''Devices''' directory at the SD-Card of your transmitter.
 Without this you will see an error message when the Spirit device is opened.

@@ Line 59: / Line 59: @@
 Now download the [https://spirit-system.com/dl/jeti/SPIRIT-3-3.zip Configuration file], which has BIN extension. The file name is
-This file should be copied to the "Devices" directory on the SD-Card of your transmitter.
+Content of this folder must be copied to the '''Devices''' directory at the SD-Card of your transmitter.
-Without it you will see the error message when the Spirit device is opened.
+Without this you will see an error message when the Spirit device is opened.
 This mean Devices directory will contain SPIRIT.bin file and SPIRIT directory with images inside.

@@ Line 8: / Line 8: @@
 To make it work you will need:
-* Jeti Duplex transmitter: DC/DS 14 or 16 or 24
+* Jeti Duplex transmitter: DC/DS 12, 14, 16 or 24
 * Jeti Duplex receiver with a free EX port.
 * Jeti Integration cable available in our stores (not for Spirit GT).

@@ Line 45: / Line 45: @@
 At the receiver side the servo connector must be connected to the EX Bus port.
 * For new REX receivers the port is called '''E1''' or '''E2''' (EXT port will not work).
-* For older EX receiver the port label is always '''EXT'''.
+* For older EX receiver the port label is always called '''EXT'''.
 <p></p>
 {{Info|[[File:Info.png]] If you are using EX receivers with attached telemetry sensor to the EXT port in this case you have two options:

@@ Line 43: / Line 43: @@
 === JETI receiver side ===
-On the receiver side the servo cable must be connected to the EX Bus port.
+At the receiver side the servo connector must be connected to the EX Bus port.
 * For new REX receivers the port is called '''E1''' or '''E2''' (EXT port will not work).
 * For older EX receiver the port label is always '''EXT'''.

@@ Line 81: / Line 81: @@
 == Integration Menu ==
-When unit is initialized you are able to enter the Jeti Integration menu.
+When unit is initialized you will be able to enter the Jeti Integration menu.
-Press the MENU button on the transmitter.
+Press the MENU button at the transmitter.
 Then select the Model menu by a rotary knob.

@@ Line 98: / Line 98: @@
 === Still can't see the Spirit? ===
-If you have everything right, but the unit is still not visible, then the only problem can be that the EX Bus port of your receiver is configured to a different protocol.
+If you have everything right but the unit is still not visible, then the only problem can be that the EX Bus port of your receiver is configured to a different protocol.
 In this case, enter the configuration menu of your receiver in the Device Explorer - the entry has name of your receiver.

@@ Line 96: / Line 96: @@
 [[File:Jeti-menu3.png]]
-=== Stil can't see the Spirit? ===
+=== Still can't see the Spirit? ===
 If you have everything right, but the unit is still not visible, then the only problem can be that the EX Bus port of your receiver is configured to a different protocol.