Jive Telemetry/en - Revision history

FuzzyBot: Importing a new version from external source

2017-08-10T15:26:27Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2017-07-11T06:47:16Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2017-07-01T13:10:01Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2017-05-22T09:15:21Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2017-05-22T09:10:17Z

Importing a new version from external source

New page

<languages />

Kontronik Jive ESC has telemetry feature built-in in the dedicated port (JMP label). This allows telemetry data transmission to the unit.

== Telemetry Cable ==
To allow the telemetry data transmission the '''Telem UNI cable''' is required. This cable is available in our [http://store.spirit-system.com/en/accessories/34-telemuni-cable.html Eshop].

[[File:telemuni.png|280px]]

{{Quote|'''It is necessary to modify the cable! Swap orange and red wires in the servo connector of the Telem UNI cable. The Orange wire must be in the middle.'''}}

== Interfacing ==

Connect the Telemetry cable to the primary Spektrum satellite port in the unit. Smaller Spirit units will utilize the one native Spektrum satellite port.

[[File:unit-telemuni.jpg|350px]]

{{Quote|Do not connect the Telem UNI cable without required modification! This can damage the unit permanently.}}

Servo connector of the Telem UNI cable should be connected to the ESC - programming port (JMP).

[[File:esc-ji.jpg|350px]]

== Spirit Settings ==

Power up the ESC and start the Spirit Settings as usually.

=== Telemetry activation ===

As the last step you have to set the ESC Telemetry in the Spirit Settings software.

Go to the '''Advanced/Telemetry settings''' and set the '''Kontronik Jive''' option.

[[File:esc-telem-ji.png|400px]]

Then close the window and save the settings ''(CTRL+S)''. Finally, reconnect battery from the ESC.

From this moment, everything should work.

== Displaying telemetry data ==

You can display telemetry data directly in your radio from now.

How to display the data is described in the integration guides:
*[[Jeti_Integration|JETI Duplex]]
*[[OpenTX_Integration|FrSky Taranis & Horus]]
*[[Hott_Integration|Graupner HoTT]]

== Supported models ==

{| class="servolist"
!
Model
!
Battery Voltage
!
Battery Current
!
BEC Voltage
!
Consumed Capacity
!
ESC Temperature
|-
| JIVE 80+ HV
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
|-
| JIVE 120+ HV
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
|-
| JIVE 80+ LV
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
|-
| JIVE 120+ LV
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
|}
<p></p>
{{Info|[[File:Info.png]] Consumed Capacity is calculated from the Current Consumption.}}

@@ Line 46: / Line 46: @@
 *[[OpenTX_Integration|FrSky Taranis & Horus]]
 *[[Hott_Integration|Graupner HoTT]]
 == Supported models ==

@@ Line 82: / Line 82: @@
 |-
 | JIVE 100+ LV
 | style="text-align:center;" |✔
 | style="text-align:center;" |✔

@@ Line 62: / Line 62: @@
+!
 ESC Temperature
 |-
 | JIVE 80+ HV
 | style="text-align:center;" |✔
 | style="text-align:center;" |✔
@@ Line 71: / Line 74: @@
 |-
 | JIVE 120+ HV
 | style="text-align:center;" |✔
 | style="text-align:center;" |✔
@@ Line 78: / Line 82: @@
 |-
 | JIVE 80+ LV
 | style="text-align:center;" |✔
 | style="text-align:center;" |✔
@@ Line 85: / Line 90: @@
 |-
 | JIVE 120+ LV
 | style="text-align:center;" |✔
 | style="text-align:center;" |✔