FuzzyBot: Updating to match new version of source page

2026-07-23T07:26:45Z

Updating to match new version of source page

Admin: Created page with "Telemetrie OMP"

2023-11-29T11:44:14Z

Created page with "Telemetrie OMP"

New page

<languages />

OMP M4 ESC has telemetry feature built-in in the Programming port. This allows telemetry data transmission to the unit.

== Telemetry Cable ==
To allow the telemetry data transmission the '''Telem OMP cable''' is required. This cable is available in our [http://store.spirit-system.com/en/accessories/34-telemuni-cable.html Eshop].

[[File:telemomp.jpg|280px]]

{{Quote|We do not recommend to make this cable at home since improper connection will cause permanent damage of the unit.
The Red wire must be disconnected always!}}

== Interfacing ==

Connect the Telemetry cable to the primary Spektrum satellite port ('''SAT1''') in the unit - apply for Spirit 2, Spirit RS, Spirit Pro, Spirit GT, Spirit GTR, Spirit W1.

There is no support for Spirit v1 units.

[[File:unit-telemuomp.jpg|350px]]

Servo connector of the Telem OMP cable should be connected to the ESC - programming port. Make sure to connect Orange wire of the Telem OMP cable at the TX pin. Brown pin at the '''-''' pin.

[[File:esc-ompm4.jpg|350px]]

== Spirit Settings ==

Power up the ESC and start the Spirit Settings as usually.

=== Telemetry activation ===

As the last step you have to set the ESC Telemetry in the Spirit Settings software.

Go to the '''Advanced/Telemetry settings''' and set the '''OMP M4''' option.

[[File:esc-telem-omp.png|400px]]

Then close the window and save the settings ''(CTRL+S)''. Finally, reconnect battery from the ESC.

From this moment, everything should work.

== Displaying telemetry data ==

You can display telemetry data directly in your radio from now.

How to display the data is described in the integration guides:
*[[Jeti_Integration|JETI Duplex]]
*[[OpenTX_Integration|OpenTX]]
*[[EthOS|FrSky EthOS]]
*[[Hott_Integration|Graupner HoTT]]
*[[Spektrum_Integration|Spektrum Integration]]
*[[Futaba Telemetry|Futaba Telemetry]]


{{Info|[[File:Info.png|18px|]] HobbyWing ESC can transmit Current and Consumed Capacity only when there is a load. Without main blades it will show zero value..}}


== Supported models ==

{| class="servolist"
!
Model
!
Battery Voltage
!
Battery Current
!
Consumed Capacity
!
ESC Temperature
!
RPM
|-
| OMP M4
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
|}

{{Info|[[File:Info.png]] Consumed Capacity is calculated from the Current Consumption.}}

@@ Line 1: / Line 1: @@
 <languages />
-OMP M4 ESC has telemetry feature built-in in the Programming port. This allows telemetry data transmission to the unit.
+This guide fits '''OMP''' and '''ZTW''' ESCs. OMP and ZTW and ESC has telemetry feature built-in in the Programming port. This allows telemetry data transmission to the unit.
 == Telemetry Cable ==
-To allow the telemetry data transmission the '''Telem OMP cable''' is required. This cable is available in our [http://store.spirit-system.com/en/accessories/34-telemuni-cable.html Eshop].
+To allow the telemetry data transmission the '''Telem OMP cable''' is required. This cable is available in our [https://store.spirit-system.com/en/accessories/65-telemomp-cable.html Eshop].
 [[File:telemomp.jpg|280px]]
@@ Line 13: / Line 19: @@
 == Interfacing ==
-Connect the Telemetry cable to the primary Spektrum satellite port ('''SAT1''') in the unit - apply for Spirit 2, Spirit RS, Spirit Pro, Spirit GT, Spirit GTR, Spirit W1.
+Connect the Telemetry cable to the primary Spektrum satellite port ('''SAT1''') in the unit - apply for Spirit 2, Spirit 3, Spirit RS, Spirit Pro, Spirit GT, Spirit GTR, Spirit W1.
 There is no support for Spirit v1 units.
@@ Line 19: / Line 25: @@
 [[File:unit-telemuomp.jpg|350px]]
-Servo connector of the Telem OMP cable should be connected to the ESC - programming port. Make sure to connect Orange wire of the Telem OMP cable at the TX pin. Brown pin at the '''-''' pin.
+Servo connector of the Telem OMP cable should be connected to the ESC - programming port. Make sure to connect Orange wire of the Telem OMP cable at the '''TX pin'''. Brown pin at the '''-''' pin.
 [[File:esc-ompm4.jpg|350px]]
@@ Line 44: / Line 52: @@
 How to display the data is described in the integration guides:
 *[[Jeti_Integration|JETI Duplex]]
 *[[OpenTX_Integration|OpenTX]]

OMP Telemetry/cs - Revision history

FuzzyBot: Updating to match new version of source page

Admin: Created page with "Telemetrie OMP"