Problems and Solutions/en - Revision history

FuzzyBot: Importing a new version from external source

2023-08-19T14:07:21Z

Importing a new version from external source

2018-01-24T08:57:40Z

Updating to match new version of source page

2018-01-10T20:47:44Z

Importing a new version from external source

2018-01-10T20:44:37Z

Importing a new version from external source

2018-01-10T20:40:43Z

Updating to match new version of source page

2017-09-21T08:21:36Z

Importing a new version from external source

2017-02-16T12:08:31Z

Updating to match new version of source page

2017-01-11T12:05:34Z

Updating to match new version of source page

2017-01-11T11:34:03Z

Updating to match new version of source page

2016-09-16T09:16:46Z

Importing a new version from external source

@@ Line 12: / Line 12: @@
 |Increase cyclic gain and/or increase the gyro gain in the transmitter. Add exponential in the transmitter.
 |- style="vertical-align:top;"
-|Aggressive cyclic pitch movement or fast forward flight leads to rapid, large tail oscillations
+|Aggressive cyclic, collective pitch movement or fast forward flight leads to rapid, large tail oscillations
 |Decrease pirouette consistency in the ''Advanced tab'' gradually by 10 until this disappears. Check the tail mechanics for binding.
 |- style="vertical-align:top;"

@@ Line 1: / Line 1: @@
 <languages />
 <div id="up"></div>
 {| class="problems" style="text-align: left; width: 100%;"

@@ Line 26: / Line 26: @@
 |- style="vertical-align:top;"
 |Pirouette is too slow/fast
-|Increase/decrease rotation speed for rudder in ''Sensor tab''.
+|Increase/decrease rotation speed for Rudder in the ''Sensor tab''.
 |- style="vertical-align:top;"
 |Servos jitter randomly without external influences

@@ Line 25: / Line 25: @@
 |Increase/decrease rotation speed for Cyclic in the ''Sensor tab''.
 |- style="vertical-align:top;"
-|Model pirouette rotation is too slow/fast
+|Pirouette is too slow/fast
 |Increase/decrease rotation speed for rudder in ''Sensor tab''.
 |- style="vertical-align:top;"

@@ Line 21: / Line 21: @@
 |Tail oscillates rapidly
 |Decrease gyro gain in the transmitter.
 |- style="vertical-align:top;"
 |Model pirouette rotation is too slow/fast

@@ Line 48: / Line 48: @@
 |Positive and negative collective pitch is unequal
 |Enable Servos/Subtrim (tuning) and verify that servo arms are perpendicular, swashplate perfectly leveled and there is 0° between main blades. If yes, use the Servo Travel Correction.
 |}
 <div class=noprint>

@@ Line 42: / Line 42: @@
 |Swashplate is jumping in a cycle when initialization is finished
 |The unit was started with the Rescue mode engaged. Turn off the rescue from your transmitter.
-|-- style="vertical-align:top;"
+|- style="vertical-align:top;"
 |Rudder stop is not equal for both sides
 |Check rudder servo center position, rudder mechanics. You can also try to lower rudder limit for the side where bounce-back occur.
 |}

@@ Line 3: / Line 3: @@
-{| class="problems" style="text-align: left; width: 75%;"
+{| class="problems" style="text-align: left; width: 100%;"
 |'''Problem description'''
 |'''Solution'''

@@ Line 7: / Line 7: @@
 |- style="vertical-align:top;"
 |style="width: 50%;"|Swashplate or tail drifts after initialization
 |Check trims and subtrims. Sticks in neutral position must be 0%, see the ''Diagnostics tab''. Increase Stick deadband in ''Advanced tab''.
 |- style="vertical-align:top;"