Rescue (Automatic) - Revision history

Admin at 19:42, 24 November 2025

2025-11-24T19:42:51Z

Admin at 06:37, 24 June 2022

2022-06-24T06:37:10Z

Admin at 06:36, 24 June 2022

2022-06-24T06:36:49Z

Admin at 06:27, 24 June 2022

2022-06-24T06:27:50Z

Admin: Marked this version for translation

2022-06-24T06:20:40Z

Marked this version for translation

Admin at 06:20, 24 June 2022

2022-06-24T06:20:32Z

Admin at 08:44, 24 November 2021

2021-11-24T08:44:20Z

Admin at 08:42, 24 November 2021

2021-11-24T08:42:33Z

Admin: Marked this version for translation

2021-11-24T08:40:20Z

Marked this version for translation

Admin at 08:39, 24 November 2021

2021-11-24T08:39:55Z

@@ Line 5: / Line 5: @@
 <!--T:16-->
-This feature is available only for '''Spirit GT''' and '''Spirit GTR'''. Pilots with other units can use similar function called '''Altitude Limit''' that is available for all with Spirit GeoLink module.
+This feature is available only for '''Spirit GT'''. '''Spirit GTR''' and '''Spirit W1'''. Pilots with other units can use similar function called '''Altitude Limit''' that is available for all with Spirit GeoLink module.
 <!--T:17-->

@@ Line 27: / Line 27: @@
 <!--T:20-->
-# Set Stabi/Function to '''Selected by Channel'''
+# Set Stabi/Function to '''Selected by Channel'''.
-# Assign a free channel in the ''General - Channels'' (right side of the window) and choose function '''F: Rescue (Automatic)'''</translate>
+# Assign a free channel in the ''General - Channels'' (right side of the window) and choose function '''F: Rescue (Automatic)'''.
 # Now you can engage Rescue (Automatic) with assigned switch in your radio.
 It will start rescue automatically anytime when model will drop under level.
-Triggering level is programmed during flight from altitude when you engage the function.
+Triggering level is programmed during flight from altitude when you engage the function.</translate>
 == <translate><!--T:4-->

@@ Line 28: / Line 28: @@
 <!--T:20-->
 # Set Stabi/Function to '''Selected by Channel'''
-# Assign a free channel in the ''General - Channels'' and function '''F: Rescue (Automatic)'''</translate>
+# Assign a free channel in the ''General - Channels'' (right side of the window) and choose function '''F: Rescue (Automatic)'''</translate>
 # Now you can engage Rescue (Automatic) with assigned switch in your radio.

@@ Line 29: / Line 29: @@
 # Set Stabi/Function to '''Selected by Channel'''
 # Assign a free channel in the ''General - Channels'' and function '''F: Rescue (Automatic)'''</translate>
 == <translate><!--T:4-->

@@ Line 4: / Line 4: @@
 The Rescue mode is used for automatic model recovery when it dropped under pre-programmed altitude.
 This feature is available only for '''Spirit GT''' and '''Spirit GTR'''. Pilots with other units can use similar function called '''Altitude Limit''' that is available for all with Spirit GeoLink module.
 The Rescue, so called ''Bailout'', is activated by the pilot remotely with a preferred switch on the transmitter.
 It can be engaged whenever in flight, but not during lift off or landing.</translate>
@@ Line 17: / Line 19: @@
 We highly recommend to use a ''2-state switch'' for this feature..</translate>
-== <translate>Configuration</translate> ==
+== <translate><!--T:18-->
-<translate>There are 3 possible ways how to configure the Rescue (Automatic).
+<translate><!--T:19-->
 The easiest way (available from firmware version 3.4.0) is following:
 # Set Stabi/Function to '''Selected by Channel'''
 # Assign a free channel in the ''General - Channels'' and function '''F: Rescue (Automatic)'''</translate>

@@ Line 26: / Line 26: @@
 #<translate><!--T:9-->
 The model will ascend only for period of 1,5 second.</translate>
-#<translate>After 1,5 second pilot will regain full control and can continue flying even when function is active.</translate>
+#<translate><!--T:13-->
-#<translate>When model will drop under altitude level at which the Rescue (Automatic) was activated it will engage the Rescue on its own and it will continue from Step 2.</translate>
+After 1,5 second pilot will regain full control and can continue flying even when function is active.</translate>
-#<translate>After automatic recovery that will last always 1,5 second only, pilot can always fly normally and all the steps are repeated if model will drop under Altitude that is used as treshold.</translate>
+#<translate><!--T:14-->
 <p></p>
 {{Info|[[File:Info.png|18px|]] <translate><!--T:10-->

@@ Line 7: / Line 7: @@
 <translate><!--T:2-->
-Whenever it is needed, activate the Rescue. From this point, unit will learn altitude at which you want to rescue model automatically. This altitude is in memory as long as feature is remained activated with assigned switch. When function is turned off and on again, it will learn new altitude limit for the Rescue.</translate>
+Whenever it is needed, activate the Rescue. From this point, unit will learn altitude at which you want to rescue model automatically. This altitude is in memory as long as feature is remained activated with assigned switch. When function is turned off and on again, it will learn new altitude limit for the Rescue.
 <translate><!--T:3-->
@@ Line 24: / Line 26: @@
 #<translate><!--T:9-->
 The model will ascend only for period of 1,5 second.</translate>
-#<translate>After 1.5 second pilot will regain full control and can continue flying.</translate>
+#<translate>After 1,5 second pilot will regain full control and can continue flying even when function is active.</translate>
-#<translate>When model will drop under level at which the Rescue (Automatic) was activated it will engage the Rescue on its own and it will continue from Step 2.</translate>
+#<translate>When model will drop under altitude level at which the Rescue (Automatic) was activated it will engage the Rescue on its own and it will continue from Step 2.</translate>
 #<translate>After automatic recovery that will last always 1,5 second only, pilot can always fly normally and all the steps are repeated if model will drop under Altitude that is used as treshold.</translate>
 <p></p>