SPM4649T - Revision history

Admin: Marked this version for translation

2020-01-30T21:00:21Z

Marked this version for translation

Admin at 20:58, 30 January 2020

2020-01-30T20:58:27Z

Admin at 20:52, 30 January 2020

2020-01-30T20:52:28Z

Admin at 20:41, 30 January 2020

2020-01-30T20:41:09Z

Admin at 20:40, 30 January 2020

2020-01-30T20:40:00Z

Admin at 20:38, 30 January 2020

2020-01-30T20:38:40Z

Admin: Created page with " The receiver is able to transfer everything including channel data and telemetry. This mean that you will not need to connect anything else except this...."

2020-01-30T20:36:49Z

Created page with "<translate> The receiver is able to transfer everything including channel data and telemetry. This mean that you will not need to connect anything else except this...."

New page

<translate>
The receiver is able to transfer everything including channel data and telemetry. This mean that you will not need to connect anything else except this.</translate>

<translate>
By using the '''Jeti integration cable''' you will not need any additional modification to the receiver. In case you do not have this cable, you can make one easily with a needle and a spare servo plug.</translate>


{{Info|[[File:Info.png|18px|]] <translate>
In case that your SPM4649T receiver is not bound yet, you can do so by a '''Bind plug'''. Connect the Bind plug to the servo socket. Then power up the receiver (you can use BEC power supply and/or free port in the unit such as CH0 or AUX2).
Optional satellites can be bound normally as described in the</translate> [[Wiring#CONNECTION_OF_SPEKTRUM_DSM2.2FX_SATELLITE|<translate>
Manual</translate>]].}}


:{| style="width: 90%;"
|-
| style="width: 15%;"|'''SPM4649T <translate>
receiver</translate>'''
|<translate>
Jeti integraction cable must be connected to the Servo socket. This socket is used also for Binding.</translate>
|-
| style="width: 15%;"|'''<translate>
Spirit unit</translate>'''
|<translate>
Other end of the Jeti integration cable should be connected so that Orange wire is in the AIL pin. Powering plug with Red and Brown wires in the RUD port. ''(see the photo)''</translate>
|}

[[File:Spektrum-connection.jpg|400px|SPM4649T receiver]]
[[File:Jeti-wiring.jpg|400px|Spirit Pro unit]]

=== <translate>
Spektrum satellites (optional)</translate> ===

<translate>
To improve receiving capabilities you can connect additional Spektrum satellites. So the combination can be following:
* '''Spirit 2''' - 1x SPM4649T + 0-2x Spektrum satellites
* '''Spirit Pro''' - 1x SPM4649T + 0-2x Spektrum satellites
* '''Spirit''' - 1x SPM4649T + 0-1x Spektrum satellites
* '''µSpirit''' - 1x SPM4649T + 0-1x Spektrum satellites</translate>

{{Info|[[File:Info.png|18px|]] <translate>
In case that the [[ESC telemetry]] is used, the primary satellite can't be connected. For the Castle Creations and Kontronik Kosmik/Jive Pro ESC telemetry primary satellite can be still used.</translate>}}

== <translate>
Spirit Settings</translate> ==

<translate>
Now you are ready to power up the unit. If your Power supply is not connected yet, we recommend to connect it to the AUX1, AUX2 and/or CH0 port.
Before you can utilize the Spektrum integration connection, it is important to set the '''Spektrum DSM2/X''' receiver type in the General tab of the software. Please start the Spirit Settings and change the receiver type as displayed on the photo.
Then save the settings (e.g. by ''CTRL+S'') or the ''Backup tab/Unit - Save'' and restart the unit.</translate>

[[File:Spektrum-settings.png|thumb|center]]

@@ Line 55: / Line 55: @@
 [[File:Spektrum-settings.png|thumb|center]]
-== <translate>Radio Integration</translate> ==
+== <translate><!--T:83-->
-<translate>If you want to use Integration and Telemetry features please continue with [[Spektrum Integration]] page.</translate>
+<translate><!--T:84-->

← Older revision		Revision as of 20:58, 30 January 2020
Line 57:		Line 57:
	== <translate>Radio Integration</translate> ==		== <translate>Radio Integration</translate> ==

−	<translate>If you want to use Integration and Telemetry features please ~~read~~ [[Spektrum Integration]] page.</translate>	+	<translate>If you want to use Integration and Telemetry features please continue with [[Spektrum Integration]] page.</translate>

← Older revision		Revision as of 20:40, 30 January 2020
Line 55:		Line 55:
	== <translate>Radio Integration</translate> ==		== <translate>Radio Integration</translate> ==

−	<translate>If you want to use Integration and Telemetry features please read [Spektrum Integration] page.</translate>	+	<translate>If you want to use Integration and Telemetry features please read [[Spektrum Integration]] page.</translate>

← Older revision		Revision as of 20:38, 30 January 2020
Line 52:		Line 52:

	[[File:Spektrum-settings.png\|thumb\|center]]		[[File:Spektrum-settings.png\|thumb\|center]]
		+
		+	== <translate>Radio Integration</translate> ==
		+
		+	<translate>If you want to use Integration and Telemetry features please read [Spektrum Integration] page.</translate>

@@ Line 4: / Line 4: @@
 <translate><!--T:74-->
 By using the '''Jeti integration cable''' you will not need any additional modification to the receiver. In case you do not have this cable, you can make one easily with a needle and a spare servo plug.</translate>
 <p></p>

@@ Line 1: / Line 1: @@
 <translate><!--T:10-->
-The receiver is able to transfer everything including channel data and telemetry. This mean that you will not need to connect anything else except this.</translate>
+SPM4649T is telemetry enabled receiver that is able to transfer all channel data and telemetry at the same time. This mean that you will not need to connect anything else except one cable.</translate>
 <translate><!--T:74-->