SpiritW1 Wiring - Revision history

Admin: Marked this version for translation

2026-08-18T09:41:04Z

Marked this version for translation

2026-08-18T09:40:56Z

2026-04-01T09:42:59Z

2026-04-01T09:42:06Z

2024-01-11T11:44:26Z

2024-01-11T11:35:45Z

2024-01-09T13:11:28Z

2024-01-09T13:09:48Z

2024-01-09T13:06:23Z

2023-12-22T15:28:52Z

@@ Line 1: / Line 1: @@
 <languages />
 __NOTOC__
-=3 <translate>Wiring</translate>=
+=3 <translate><!--T:25-->
 <translate><!--T:1-->
 '''Spirit W1''' has support for 4x swashplate, 1x tail and 1x throttle servos.
 '''Spirit W3''' has support for 3x swashplate, 1x tail and 1x throttle servos.

@@ Line 68: / Line 68: @@
 <translate><!--T:15-->
-BEC, Battery or Backup power supply should be connected always at '''THR''', '''E1''' and '''AUX''' ports.</translate>
+BEC, Battery or Backup power supply should be connected always at '''THR''', '''T1''' and '''AUX''' ports.</translate>
 <translate><!--T:16-->

@@ Line 20: / Line 20: @@
 <translate><!--T:4-->
-According following diagrams you can connect servos to the Spirit W1.
+According following diagrams you can connect servos to the Spirit W1/W3.
 If some of your servos are not 1520μs center pulse, please connect the servo later during Setup Wizard process.</translate>
@@ Line 29: / Line 29: @@
 <p></p>
 <translate><!--T:24-->
-* '''CH0''' - Optional 2nd Elevator Servo</translate>
+* '''CH0''' - Optional 2nd Elevator Servo (available only with Spirit W1)</translate>
 <translate><!--T:6-->

@@ Line 4: / Line 4: @@
 <translate><!--T:1-->
 '''Spirit W1''' has support for 4x swashplate, 1x tail and 1x throttle servos.
 <!--T:23-->

@@ Line 1: / Line 1: @@
 <languages />
 __NOTOC__
-=4 <translate>Wiring</translate>=
+=3 <translate>Wiring</translate>=
 <translate><!--T:1-->
 '''Spirit W1''' has support for 4x swashplate, 1x tail and 1x throttle servos.

@@ Line 74: / Line 74: @@
 <p></p>
 {{Quote|'''<translate><!--T:22-->
-Do not connect any wire to X pin. This pin is shared between Spirit and internal receiver. It is used for future purposes. Connecting something at the X pin can result in loss of control!</translate>'''}}
+Do not connect any wire to X pin. This pin is shared with internal Spirit RX receiver. Only if using external receiver this pin can be used!</translate>'''}}
 <p></p>

@@ Line 9: / Line 9: @@
 <!--T:2-->
-Additionally you can utilize ESC telemetry.</translate>
+Additionally you can utilize [[ESC telemetry|ESC Telemetry]] and [[GeoLink|GeoLink GPS/GNSS module]].</translate>
 [[File:spiritw1-detail.jpg|class=smallwidth]]

@@ Line 5: / Line 5: @@
 <!--T:23-->
-It has also 2x independent telemetry ports which mean you can attach directly two WAVE sensors.
+It has also 2x independent telemetry ports which mean you can attach directly two Spirit Wave sensors.
 Moreover you can optionally connect a backup receiver.

@@ Line 11: / Line 11: @@
 Additionally you can utilize ESC telemetry.</translate>
-[[File:spiritrs-detail.jpg|class=smallwidth]]
+[[File:spiritw1-detail.jpg|class=smallwidth]]
 == <translate><!--T:3-->