Spirit Wave Binding - Revision history

Admin at 13:49, 19 January 2026

2026-01-19T13:49:21Z

2025-11-27T14:18:31Z

2024-10-24T12:46:20Z

2024-10-24T12:46:14Z

2024-10-21T07:59:29Z

2024-10-17T13:31:21Z

2024-10-17T13:30:17Z

2024-10-17T13:14:36Z

@@ Line 35: / Line 35: @@
 {{Info|[[File:Info.png]] <translate>If Spirit RX7 is Powered On for 30 seconds or more in the Bind mode, it will remove previously saved bind data.</translate>}}
 <p></p>
 == <translate>Binding with Wave</translate> ==

@@ Line 3: / Line 3: @@
 = <translate>Binding Procedure</translate> =
-Binding is two side operation, in which Radio and Receiver is put into the Binding mode. Both will learn how to talk to each other and from this time they will transmit both channel data, telemetry and allow remote configuration. Bind Date are stored at both sides. Model that is created in your Radio is matched with one specific receiver.
+Binding is two side operation, in which Radio and Receiver is put into the Binding mode at the same time. Both will learn how to talk to each other and from this time they will transmit both channel data, telemetry and allow remote configuration. Bind Date are stored at both sides. Model that is created in your Radio is matched with one specific receiver.
 == Spirit W1 ==

@@ Line 3: / Line 3: @@
 = <translate>Binding Procedure</translate> =
-Binding is two side operation, in which Radio and Receiver is put into the Binding mode. Both will learn how to talk to each other and from this time. Bind Date are stored at both sides. Model that is created in your Radio is matched with one specific receiver.
+Binding is two side operation, in which Radio and Receiver is put into the Binding mode. Both will learn how to talk to each other and from this time they will transmit both channel data, telemetry and allow remote configuration. Bind Date are stored at both sides. Model that is created in your Radio is matched with one specific receiver.
 == Spirit W1 ==

← Older revision		Revision as of 13:30, 17 October 2024
Line 2:		Line 2:

	= <translate>Binding Procedure</translate> =		= <translate>Binding Procedure</translate> =
		+
		+	Binding is two side operation, in which Radio and Receiver is put into the Binding mode. Both will learn how to talk to each other and from this time. Bind Date are stored at both sides. Model that is created in your Radio is matched with one specific receiver.

	== Spirit W1 ==		== Spirit W1 ==

@@ Line 36: / Line 36: @@
 <p></p>
-== Binding with Wave ==
+== <translate>Binding with Wave</translate> ==
-#You can always Bind any Wave receiver by going to the '''Model/Receiver''' menu.
+<translate>#You can always Bind any Wave receiver by going to the '''Model/Receiver''' menu.
 #Press the '''Bind button''' after powering up a receiver with a Bind plug. (Spirit RX7 or Spirit W1)
 #After successfull binding you will be notified at the Display. Binding will take no more than 500 ms.
-#Bind plug can be removed.
+#Bind plug can be removed.</translate>
 [[File:wave-bind.png|480px|center]]

@@ Line 1: / Line 1: @@
 __NOTOC__
 <languages/>
 = <translate>Binding Procedure</translate> =

← Older revision		Revision as of 13:14, 17 October 2024
Line 17:		Line 17:

	{{Info\|[[File:Info.png]] <translate>If Spirit W1 is Powered On for 30 seconds or more in the Bind mode, it will remove previously saved bind data.</translate>}}		{{Info\|[[File:Info.png]] <translate>If Spirit W1 is Powered On for 30 seconds or more in the Bind mode, it will remove previously saved bind data.</translate>}}
		+	<p></p>
		+
		+	== Spirit RX7 ==
		+	<translate>In order to Bind Spirit RX7 with your Wave radio use supplied <b>Bind plug</b>.</translate>
		+
		+	{{Info\|[[File:Info.png]] <translate>If Spirit RX7 is new (no Bind Data available) a Bind Plug is not required and you can continue with the following section '''Binding with Wave'''.</translate>}}
		+	<p></p>
		+
		+	<translate><!--T:3-->
		+	#Insert '''Bind plug''' at the '''BIND port''' and connect Power supply to the Spirit RX7 unit. You can connect BEC or 1-3S Battery at any port.
		+	#Perform binding according following '''Binding with Wave''' section.</translate>
		+
		+	[[File:spritrx7-bind.jpg\|class=halfwidth\|center]]
		+
		+	{{Info\|[[File:Info.png]] <translate>If Spirit RX7 is Powered On for 30 seconds or more in the Bind mode, it will remove previously saved bind data.</translate>}}
	<p></p>		<p></p>