TelMe Telemetry/en - Revision history

FuzzyBot: Importing a new version from external source

2023-02-08T07:56:26Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2020-02-28T12:19:24Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2018-12-17T17:33:08Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2018-12-17T11:57:09Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2018-12-14T13:05:51Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2018-12-10T14:28:00Z

Importing a new version from external source

New page

<languages />

Kontronik ESCs are utilizing special 5-pin port connector for telemetry data transmission to the unit.
To allow the ESC telemetry, it is necessary to have updated ESC to at least 1.13 firmware version. Older versions do not support TelMe protocol.

== Telemetry Cable ==
To allow the telemetry data transmission the '''Telem KONTRONIK v2 cable''' is required. This cable is available in our [http://store.spirit-system.com/en/accessories/47-telemkontronikv2-cable.html Eshop].

[[File:telemkontronikv2.png|280px]]

{{Quote|We do not recommend to make this cable at home since improper connection will cause permanent damage of the unit.}}

== Interfacing ==

Connect the Telemetry cable to the primary Spektrum satellite port in the unit. Smaller Spirit units will utilize the one native Spektrum satellite port (μSpirit - SAT port).

[[File:unit-telemuni.jpg|350px]]

Servo connector of the Telem KONTRONIK v2 cable should be connected to the ESC. In case of Kontronik KOSMIK you can select any free port.

[[File:esc-kontronik.jpg|350px]]

== Spirit Settings ==

Power up the ESC and start the Spirit Settings as usually.

=== Telemetry activation ===

As the last step you have to set the ESC Telemetry in the Spirit Settings software.

Go to the '''Advanced/Telemetry settings''' and set the '''Kontronik TelMe''' option.

[[File:esc-telem-telme.png|400px]]

Then close the window and save the settings ''(CTRL+S)''. Finally, reconnect battery from the ESC.

From this moment, everything should work.

== Displaying telemetry data ==

You can display telemetry data directly in your radio from now.

How to display the data is described in the integration guides:
*[[Jeti_Integration|JETI Duplex]]
*[[OpenTX_Integration|FrSky Taranis & Horus]]
*[[Hott_Integration|Graupner HoTT]]
*[[Spektrum_Integration|Spektrum Integration]]
*[[Futaba Telemetry|Futaba Telemetry]]

== Supported models ==

{| class="servolist"
!
Model
!
Battery Voltage
!
Battery Current
!
BEC Voltage
!
Consumed Capacity
!
ESC Temperature
!
RPM
|-
| KOLIBRI 140 LV
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
|-
| JIVE PRO 80+ HV
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
|-
| JIVE PRO 120+ HV
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
|-
| KOSMIK 160 HV
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
|-
| COOL KOSMIK 160 HV
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
|-
| KOSMIK 200 HV
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
|-
| COOL KOSMIK 200+ HV
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
|-
| COOL KOSMIK 200 HV GOLD
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
| style="text-align:center;" |✔
|}
<p></p>

@@ Line 19: / Line 19: @@
 -pin JST connector of the Telem KONTRONIK v2 cable should be connected to the ESC. In case of Kontronik KOSMIK please use port in the middle.
-[[File:esc-kontronik.jpg|350px]]
+[[File:esc-telme.jpg|350px]]
 == Spirit Settings ==

@@ Line 17: / Line 17: @@
 [[File:unit-telemuni.jpg|350px]]
--pin JST connector of the Telem KONTRONIK v2 cable should be connected to the ESC. In case of Kontronik KOSMIK you can select any free port.
+-pin JST connector of the Telem KONTRONIK v2 cable should be connected to the ESC. In case of Kontronik KOSMIK please use port in the middle.
 [[File:esc-kontronik.jpg|350px]]

@@ Line 13: / Line 13: @@
 == Interfacing ==
-Connect the Telemetry cable to the primary Spektrum satellite port in the unit. Smaller Spirit units will utilize the one native Spektrum satellite port (μSpirit - SAT port).
+Connect the Telemetry cable to the primary Spektrum satellite (SAT1) port in the unit. Smaller Spirit units will utilize the one native Spektrum satellite port (μSpirit - SAT port).
 [[File:unit-telemuni.jpg|350px]]

@@ Line 2: / Line 2: @@
 Kontronik ESCs are utilizing special 5-pin port connector for telemetry data transmission to the unit.
-To allow the ESC telemetry, it is necessary to have updated ESC to at least 1.13 firmware version. Older versions do not support TelMe protocol.
+To allow the ESC telemetry, it is necessary to have updated ESC to at least 1.13 (JIVE PRO) and 4.14 (KOSMIK) firmware version. Older versions do not support TelMe protocol.
 == Telemetry Cable ==