Translations:Configuration/250/en - Revision history

FuzzyBot: Importing a new version from external source

2017-05-03T07:12:48Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2017-04-27T19:41:04Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2017-02-02T21:59:59Z

Importing a new version from external source

FuzzyBot: Importing a new version from external source

2016-09-19T11:50:12Z

Importing a new version from external source

New page

This is a parameter to smooth rudder movements. It also helps to stabilize the rudder – it is a kind of electronic damping. The faster the servo is, the lower the tail delay should be. For analog servos it is recommended to set this value to around 20-25. For usual digital servos it is mostly between 10 – 15. For very fast servos (~0.04s/60°) the value is 5. In case of a brushless servos it is recommended to set a value of 0 - 2.
If the value is too high, the rudder could start to oscillate or wag or could cause a slow rudder stop.

← Older revision		Revision as of 07:12, 3 May 2017
Line 1:		Line 1:
−	This is a parameter to smooth rudder movements. It also helps to stabilize the rudder – it is a kind of electronic damping. The faster the servo is, the lower the ~~tail~~ delay should be. For analog servos it is recommended to set this value to around 20-25. For ~~usual~~ digital servos it is mostly between 10 – 15. For ~~very~~ fast servos (~0.04s/60°) the value is 5. In case of a brushless servos it is recommended to set a value of 0 - 2.	+	This is parameter to smooth out a rudder movements. It also helps to stabilize the rudder – it is a kind of electronic damping, similar to a derivative term of regulation. The faster the servo is, the lower the ''Rudder delay'' should be. For analog servos it is recommended to set this value to around 20 - 25. For slower digital servos it is mostly between 10 - 15. For fast servos (~0.04s/60°) the value is around 5. In case of a brushless servos it is recommended to set the value of 0 - 2.
−	If the value is too high, the rudder could start to oscillate or wag or could cause ~~a slow~~ rudder ~~stop~~.	+	If the value is too high, the rudder could start to oscillate, wag or it could cause too smooth rudder stopping.

← Older revision		Revision as of 19:41, 27 April 2017
Line 1:		Line 1:
−	This is parameter to smooth ~~out a~~ rudder movements. It also helps to stabilize the rudder – it is a kind of electronic damping~~, similar to a derivative term of regulation~~. The faster the servo is, the lower the ~~''Rudder~~ delay'' should be. For analog servos it is recommended to set this value to around 20 - 25. For ~~slower~~ digital servos it is mostly between 10 - 15. For fast servos (~0.04s/60°) the value is ~~around~~ 5. In case of a brushless servos it is recommended to set ~~the~~ value of 0 - 2.	+	This is a parameter to smooth rudder movements. It also helps to stabilize the rudder – it is a kind of electronic damping. The faster the servo is, the lower the tail delay should be. For analog servos it is recommended to set this value to around 20-25. For usual digital servos it is mostly between 10 – 15. For very fast servos (~0.04s/60°) the value is 5. In case of a brushless servos it is recommended to set a value of 0 - 2.
−	If the value is too high, the rudder could start to oscillate, wag or it could cause ~~too smooth~~ rudder ~~stopping~~.	+	If the value is too high, the rudder could start to oscillate or wag or could cause a slow rudder stop.

← Older revision		Revision as of 21:59, 2 February 2017
Line 1:		Line 1:
−	This is a parameter to smooth rudder movements. It also helps to stabilize the rudder – it is a kind of electronic damping. The faster the servo is, the lower the ~~tail~~ delay should be. For analog servos it is recommended to set this value to around 20-25. For ~~usual~~ digital servos it is mostly between 10 – 15. For ~~very~~ fast servos (~0.04s/60°) the value is 5. In case of a brushless servos it is recommended to set a value of 0 - 2.	+	This is parameter to smooth out a rudder movements. It also helps to stabilize the rudder – it is a kind of electronic damping, similar to a derivative term of regulation. The faster the servo is, the lower the ''Rudder delay'' should be. For analog servos it is recommended to set this value to around 20 - 25. For slower digital servos it is mostly between 10 - 15. For fast servos (~0.04s/60°) the value is around 5. In case of a brushless servos it is recommended to set the value of 0 - 2.
−	If the value is too high, the rudder could start to oscillate or wag or could cause ~~a slow~~ rudder ~~stop~~.	+	If the value is too high, the rudder could start to oscillate, wag or it could cause too smooth rudder stopping.