XDFly Telemetry - Revision history

Admin at 07:06, 15 September 2025

2025-09-15T07:06:23Z

Admin at 06:54, 15 September 2025

2025-09-15T06:54:20Z

Admin at 06:54, 15 September 2025

2025-09-15T06:54:13Z

Admin: Created page with " This guide fits '''OMP''' and '''ZTW''' ESCs. OMP and ZTW and ESC has telemetry feature built-in in the Programming port. This allows tele..."

2025-09-15T06:52:49Z

Created page with "<languages /> <translate> This guide fits '''OMP''' and '''ZTW''' ESCs. OMP and ZTW and ESC has telemetry feature built-in in the Programming port. This allows tele..."

New page

<languages />

<translate>
This guide fits '''OMP''' and '''ZTW''' ESCs. OMP and ZTW and ESC has telemetry feature built-in in the Programming port. This allows telemetry data transmission to the unit.</translate>

<translate>Similarly XDFly ESCs have telemetry feature built-in. Additionally they support ESC Integration with Spirit Wave radios. Wiring is slightly different!</translate>

<translate>For '''XDFly''' ESC visit [[XDFly_Telemetry|XDFly Telemetry]] page.</translate>

== <translate>
Telemetry Cable</translate> ==
<translate>
To allow the telemetry data transmission the '''Telem UNI cable''' is required. This cable is available in our [https://store.spirit-system.com/en/accessories/65-telemuni-cable.html Eshop].</translate>

[[File:Telemuni.jpg|280px]]

{{Quote|<translate>
We do not recommend to make this cable at home since improper connection will cause permanent damage of the unit.
The Red wire must be disconnected or has to be removed always!</translate>}}

== <translate>
Interfacing</translate> ==

<translate>
Connect the Telemetry cable to the primary Spektrum satellite port ('''SAT1''') in the unit - apply for Spirit 2, Spirit RS, Spirit Pro, Spirit GT, Spirit GTR, Spirit W1.


There is no support for Spirit v1 units.</translate>

[[File:unit-telemuomp.jpg|350px]]

<translate>
Servo connector of the Telem UNI cable should be connected to the ESC - programming port. Make sure to connect Orange wire at the '''RX pin''' of the ESC.
</translate>

[[File:esc-xdfly.jpg|350px]]

== Spirit Settings ==

<translate>
Power up the ESC and start the Spirit Settings as usually.</translate>

=== <translate>
Telemetry activation</translate> ===

<translate>
As the last step you have to set the ESC Telemetry in the Spirit Settings software.</translate>

<translate>
Go to the '''Advanced/Telemetry settings''' and set the '''XDFly & ZTW & OMP''' option.</translate>

[[File:esc-telem-omp.png|400px]]

<translate>
Then close the window and save the settings ''(CTRL+S)''. Finally, reconnect battery from the ESC.</translate>

<translate>
From this moment, everything should work.</translate>

== <translate>
Displaying telemetry data</translate> ==

<translate>
You can display telemetry data directly in your radio from now.</translate>

<translate>
How to display the data is described in the integration guides:</translate>
*[[<translate>Spirit_Wave_ESC_Telemetry</translate>|Spirit Wave]]
*[[<translate>
Jeti_Integration</translate>|JETI Duplex]]
*[[<translate>
OpenTX_Integration</translate>|OpenTX]]
*[[<translate>
EthOS</translate>|FrSky EthOS]]
*[[<translate>
Hott_Integration</translate>|Graupner HoTT]]
*[[<translate>
Spektrum_Integration</translate>|Spektrum Integration]]
*[[<translate>
Futaba Telemetry</translate>|Futaba Telemetry]]

@@ Line 7: / Line 7: @@
 Telemetry Cable</translate> ==
 <translate><!--T:3-->
-To allow the telemetry data transmission the '''Telem UNI cable''' is required. This cable is available in our [https://store.spirit-system.com/en/accessories/65-telemuni-cable.html Eshop].</translate>
+To allow the telemetry data transmission the '''Telem UNI cable''' is required. This cable is available in our [https://store.spirit-system.com/en/esc-telemetry/34-telemuni-cable.html Eshop].</translate>
 [[File:Telemuni.png|280px]]

@@ Line 4: / Line 4: @@
 '''XDFly''' has telemetry feature built-in in the Programming port. This allows telemetry data transmission to the unit. Additionally it has support for ESC programming with Spirit Wave</translate>
 == <translate><!--T:2-->
 Telemetry Cable</translate> ==

@@ Line 2: / Line 2: @@
 <translate><!--T:1-->
-This guide fits '''OMP''' and '''ZTW''' ESCs. OMP and ZTW and ESC has telemetry feature built-in in the Programming port. This allows telemetry data transmission to the unit.</translate>
+'''XDFly''' has telemetry feature built-in in the Programming port. This allows telemetry data transmission to the unit. Additionally it has support for ESC programming with Spirit Wave</translate>
-−
-<translate>Similarly XDFly ESCs have telemetry feature built-in. Additionally they support ESC Integration with Spirit Wave radios. Wiring is slightly different!</translate>
 <translate>For '''XDFly''' ESC visit [[XDFly_Telemetry|XDFly Telemetry]] page.</translate>
@@ Line 13: / Line 11: @@
 To allow the telemetry data transmission the '''Telem UNI cable''' is required. This cable is available in our [https://store.spirit-system.com/en/accessories/65-telemuni-cable.html Eshop].</translate>
-[[File:Telemuni.jpg|280px]]
+[[File:Telemuni.png|280px]]
 {{Quote|<translate><!--T:31-->