Difference between revisions of "GeoLink Features/es"

Revision as of 21:56, 18 January 2019

GEOLINK ofrece una variedad de caracteristicas que pueden habilitarse bajo demanda mientras se vuela.Algunos tambien se pueden combinar para ofrecer la experiencia que desea

1 TTFF Acelerador

Esta caracteristica permite reducir significativamente el periodo en el que el modulo GEOLINK puede arreglar a los satelites de navegacion. Con algunos dispositivos lleva incluso unos minutos.Con GEOLINK este periodo se puede reducir a solo 6 segundos,mientras no se necesita respaldo de bateria.

1.1 como funciona

Cuando el modulo se enciende por primera vez en un dia determinado,se trata de encontrar un satelite.Lo hara de manera normal(sin ninguna reduccion de tiempo). Con GEOLINK esto deberia ser entre 20 y 35 segundosnormalmente(dependiendo de las condiciones).

justo despues del vuelo y el siguiente encendido,este periodo se reduce significativamente. Cuando se enciende dentro de unos minutos a horas, siempre puede notar que el tiempo requerido para la correccion se acorta

Dado que el modulo esta realizando calculos para predecir la posicion de los satelites incluso para los dias siguientes,puede seentir una mejora incluso si el modulo no se ejecuto durante 3 dias

1.2 ¿Como puede ayudarme?

Si vuelas unas pocas baterias en el mismo dia,mientras que el tiempo intermedio es inferior a una hora,los resultados son los mejores. Por lo general, inmdediatamente despues de que se inicializa la unidad SPIRIT, esta listo para volar sin necesidad de esperar mas

Si vuelas solo una bateria, pero solo cada uno o dos dias, tambien notaras los beneficios

2 Registro

GEOLINK esta registrando cada vuelo y almacena los registros en su memoria.Se esta alamacenando cada segundo, mientras que la longitud total del registro de vuelo puede alcanzar 1,5 horas. Si se excede la memoria, se eliminaran automaticamente los registros antiguos para almacenar uno nuevo. los datos registrados estan sujetos a cambios y podrian cambiar en las actualizaciones futuras.

2.1 Espeficicaciones del registro

• Up to 1.5 hour
• Up to 63 logged flights
• Recording period: 1 second

2.2 What is being logged?

• Position on Earth: Latitude and Longitude
• Altitude: relative altitude from starting point
• Speed: flying speed of the model
• Heading: direction in which model is flying
• Date and time

2.3 Log viewer

Any logged flight can be viewed on demand with Spirit Settings software. You can see flight paths directly on the map and can re-play the log in a speed you wish.

2.4 Log backup and sharing

Each log can be also backed up or shared with others easily by saving it as file to your computer. The files can be loaded and replayed in the viewer.

3 Return To Home

Whenever you will loose orientation, this function is the best option. You have to only engage the function with your transmitter and wait a moment, until the model returns to defined position.

Some other systems are taking Home position as the spot where you are powering up the model. This is not the case for Spirit with GeoLink. To increase reliability and safety significantly, we have Home position programmed in the memory. In that way model will return always at the same place repeatably while avoiding flying above pilot. Pilot can program the Home position with enough distance to maintain safety.

Pilot can anytime program the position:

• in the Spirit Settings by choosing the best spot at the map
• by transmitter command being at the place considered as a new Home.

3.1 Description

Once the feature is engaged the model will immediately change its direction to programmed home destination, wherever it is. It can work also upside down, so it does not matter what the orientation is.

All the time the rudder control will still work without any change so that pilot can yaw in any way he wish. The feature will not move with rudder at all, thus pilot will find the model rotated as it was and can change direction at any moment, even when it already returned.

Once model will return it will maintain the position so it can't fly over again.

3.2 With Altitude Hold

This feature can be combined with Altitude Hold.

4 Auto Landing

Whenever you want to land with the model you can use this feature to do so automatically.

4.1 Description

It is enough to engage the feature and the model will land at the current position. Firstly, the model will stop it's movement. Secondly it will start to descend until it will reach approximately 2 meter altitude. From this point it will be descending rather slowly and only in case that the model is not moving in other way. If the model seems to be unstable it is important to perform the Compass Calibration or Correction angle adjustment.

Once the model will land the collective pitch will remain at a neutral position (0° deflection). The motor will not turn off.

The swashplate can be controlled all the time as if Coaxial mode is enabled - to perform a slight corrections if needed.

Rudder control is identical as with a normal flying mode.

5 Position Hold

If you are learning the basics this feature can help you significantly in maintaining required spot. If you are not strong in hovering the feature will do the job for you.

5.1 Description

The model is flying similarly as with Coaxial mode. Pilot can control the model fully but all movement speed is controlled so it can't fly too fast. Rather you can fly very safely as with a Coaxial model and without undesired drifting caused by wind. Always when sticks are released the model will stop at that point and will maintain it until other steering command is given. The model can't be flipped over. This feature can work also upside down in the same way.

Rudder control is identical as with a normal flying mode.

5.2 With Altitude Hold

This feature can be combined with Altitude Hold.

6 Geo-fence

This feature allows to restrict flying area so that when flying over the model will return. Pilot can set a virtual fence in which the model is allowed to fly.

6.1 Description

When model fly over configured fence it will try to stop and return back to allowed area as fast as possible. This feature can work also upside down in the same way. Rudder control is identical as with a normal flying mode.

6.2 With Altitude Hold

This feature can be combined with Altitude Hold.

7 Altitude Hold

If pilot is unable to maintain altitude the feature can control collective pitch automatically for him.

7.1 Description

The model will try to maintain altitude at which the feature was engaged. It can work in a normal flying mode and any Stabi function. Pilot can safely change the altitude by collective pitch movements anytime. If without movement, the altitude is maintained. This feature can work also upside down in the same way.

The feature will not change anything else than collective pitch.

8 Altitude Limit

If you are worried you will forget to engage the Rescue mode in time, this feature is what you are looking for.

8.1 Description

If engaged the model will fly without any change in behavior. But as soon as the model will fly under configured altitude the Rescue mode is activated automatically until the model ascend above this level. It will be engaged for at least 1.5 seconds. Then depending on gained altitude it is turned off and pilot can continue in flight. The Rescue mode is utilizing same Collective Pitch settings as when it is engaged manually.

On the other hand if the model exceed configured upper altitude limit it will stop ascending there. The model will maintain the level and pilot can descend on will with collective pitch.

Altitude is determined from initialization point. This mean that at initialization altitude the model is at zero.