Difference between revisions of "Flashing Failed/ru"
From Spirit System Manual
(Created page with "Возможные причины:") |
(Updating to match new version of source page) |
||
(25 intermediate revisions by 2 users not shown) | |||
Line 11: | Line 11: | ||
:'''Возможные причины:''' | :'''Возможные причины:''' | ||
− | : | + | :*Неустойчивое соединение между ПК и модулем Spirit ( проверьте все кабели ) |
− | + | ||
− | + | ||
− | + | :*Bad USB interface driver in your Operating System. | |
− | + | Если проблема наблюдается под Windows, переустановите программу настройки и драйвер.Это установит правильный драйвер. Перезагрузитесь. | |
− | + | Если проблема наблюдается под Mac, используйте драйвер: [https://www.silabs.com/documents/public/software/Mac_OSX_VCP_Driver.zip OSX 11.0 Big Sur and newer] | |
− | + | Другие драйвера почти точно будут работать неправильно - особенно во время прошивки! | |
− | : | + | :'''Requirements for the Recovery process:''' |
− | + | ||
− | : | + | |
− | + | :#Правильный установленный драйвер | |
+ | :#Status LED of the unit must be pulsating after power up. | ||
− | :# | + | == Как оживить модуль == |
− | :#Start the software. '''Select | + | |
− | :#Go to the Update tab and select firmware you want to flash | + | :#Подключите модуль к ПК по USB ( '''порт SYS''' ) '''(SYS port)'''. |
− | + | :#Start the software. '''Select Recovery mode''' when prompted. | |
− | :#Power up the unit (from your BEC or a battery). | + | :#Choose correct COM port in the Connection tab first. |
− | :#In | + | :#Go to the Update tab and select firmware you want to flash. |
+ | :#Power up the unit (from your BEC or a battery) and wait until Status LED start to pulsating. | ||
+ | :#Press the Flash button and confirm - software will download firmware from Spirit Server and flashing should start immediately. | ||
+ | :#In 10 seconds, unit should be operating again without any issue. Your settings are untouched. | ||
Line 41: | Line 41: | ||
{|style="width: 100%;color: white;text-align:center;" | {|style="width: 100%;color: white;text-align:center;" | ||
− | |[[#up|↑ | + | |[[#up|↑Вверх↑]] |
|} | |} | ||
---- | ---- | ||
</div> | </div> |
Latest revision as of 21:48, 12 December 2023
1 Модуль не работает после обновления прошивки
В случае, если модуль не работает после обновления прошивки, используйте данное руководство для восстановления его работоспособности.
Главные вопрос, почему был сбой ?
- Возможные причины:
- Неустойчивое соединение между ПК и модулем Spirit ( проверьте все кабели )
- Bad USB interface driver in your Operating System.
Если проблема наблюдается под Windows, переустановите программу настройки и драйвер.Это установит правильный драйвер. Перезагрузитесь.
Если проблема наблюдается под Mac, используйте драйвер: OSX 11.0 Big Sur and newer
Другие драйвера почти точно будут работать неправильно - особенно во время прошивки!
- Requirements for the Recovery process:
- Правильный установленный драйвер
- Status LED of the unit must be pulsating after power up.
2 Как оживить модуль
- Подключите модуль к ПК по USB ( порт SYS ) (SYS port).
- Start the software. Select Recovery mode when prompted.
- Choose correct COM port in the Connection tab first.
- Go to the Update tab and select firmware you want to flash.
- Power up the unit (from your BEC or a battery) and wait until Status LED start to pulsating.
- Press the Flash button and confirm - software will download firmware from Spirit Server and flashing should start immediately.
- In 10 seconds, unit should be operating again without any issue. Your settings are untouched.