View source for Jeti Integration/de

<languages />
[[File:Jeti-display.png]]

Ab Version 1.1.0 können Sie die JETI-Integration nutzen!
Das bedeutet, Sie können Spirit-Geräte völlig mit JETI-Sendern in Echtzeit konfigurieren, ohne dass ein Computer benötigt wird.

== Requirements ==

Damit es funktioniert brauchen Sie:
* Jeti Duplex Sender: DC/DS 14 or 16 or 24
* Jeti Duplex-Empfänger mit einem freien EX-Port
* Jeti Integrationskabel in unseren Filialen erhältlich.
* [http://spirit-system.com/dl/jeti/Spirit.bin Konfigurationsdatei] für den Sender.

[[File:Jeti-cable.jpg]]

== Verkabelung ==

Das Jeti-Kabel ist in der Lage, alles zu übertragen, einschließlich Kanaldaten und Telemetrie. Das bedeutet, dass Sie nichts anderes als dieses Kabel anschließen müssen.

[[File:Jeti-wiring.jpg|thumb|left]]


Auf der Empfängerseite muss das Servokabel an den EX-Busanschluss angeschlossen werden.
* Für neue REX-Empfänger ist die Anschlussbezeichnung '''EX1''' oder '''EX2''' (EXT Anschluss funktioniert nicht).
* Bei älteren EX-Receivern ist die Anschlussbezeichnung immer '''EXT'''.

Wenn Sie EX-Empfänger mit angeschlossenem Telemetriesensor zum EXT-Anschluss verwenden, haben Sie in diesem Fall zwei Möglichkeiten:
* Benutzen Sie eine UDI-Verbindung (SRXL / SUMD-Empfängertyp)- In diesem Fall verlieren Sie die Jeti-Integration.
* Kaufen Sie einen REX-Receiver, wo Sie Telemetriesensoren und die Jeti-Integration zusammen nutzen können.

[[File:Jeti-connection.jpg|thumb|right]]

== Sender Vorbereitung ==

Laden Sie jetzt die [http://spirit-system.com/dl/jeti/Spirit.bin Konfigurationsdatei], welche die BIN-Erweiterung hat. Der Dateiname lautet "''Spirit.bin''".
This file should be copied to the "Devices" directory on the SD-Card of your transmitter.
Without it you will see the error message when the Spirit device is opened.

You can copy it by connecting the micro USB cable to the transmitter similarly as to an USB flash drive.
When cable is attached to the transmitter you have to confirm the USB connection.
Then simply drag and drop it to the ''Devices'' directory as you are used to.

''It is very important to use the same version of the BIN file as your current firmware in the unit.
If the versions are not matching then an incompatibility issues could occur.''

== Spirit Settings ==

Now you are ready to power up the unit. If your Power supply is not connected yet, we recommend to connect it to the AUX1, AUX2 and/or CH0 port.
Before you can utilize the Jeti Integration and EX Bus connection, it is important to set the EX Bus receiver type in the General tab of the software. Please start the Spirit Settings and change the receiver type as displayed on the photo.
Then save the settings (e.g. by ''CTRL+S'') or the ''Backup tab/Unit - Save'' and restart the unit.

[[File:Jeti-settings.png|thumb|center]]

== Integration Menu ==

When unit is initialized you are able to enter the Jeti Integration menu.
Press the MENU button on the transmitter.

Then select the Model menu by a rotary knob.

[[File:Jeti-menu1.png]]

And then enter the Device Explorer menu.

[[File:Jeti-menu2.png]]

There, if the wiring and receiver type is correct, you will see the Spirit entry.

[[File:Jeti-menu3.png]]

=== Stil can't see the Spirit? ===

If you have everything right, but the unit is still not visible, then the only problem can be that the EX Bus port of your receiver is configured to a different protocol.

In this case, enter the configuration menu of your receiver in the Device Explorer - the entry has name of your receiver.
Change the Serial Link to the EX Bus.
In case of the REX receivers you can assign EX1 or EX2 port..

[[File:Jeti-menurx.png]]

== Usage ==

Whenever you want to configure a parameter, go to the Model/Device Explorer/Spirit.
There the Menu Layout is nearly identical with the PC software to have easy navigation.

It is working in the same way as when the PC software is connected. This mean that when Jeti Integration menu is opened, you can change even the basic parameters that could affect the helicopter significantly.

{{Quote|'''Never perform the configuration when flying!'''}}

When using the Bank Switching or Real-Time tuning features the menu will take full control of it. The unit will not react to a Switch position changes.
For the Bank Switching there is a menu ''Bank Switching'' where you can manually change the banks.

Do not forget to click the '''Save Settings''' when you want to save a changes permanently.

[[File:Jeti-menusave.png]]

Enjoy the integration!