Difference between revisions of "Graupner SUMD"
| (14 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
| + | <languages /> | ||
| + | |||
| + | <translate><!--T:1--> | ||
With Graupner HoTT radios you can use fully digital, single-line SUMD protocol. | With Graupner HoTT radios you can use fully digital, single-line SUMD protocol. | ||
| − | For the connection only normal servo cable is required. | + | For the connection only normal servo cable is required.</translate> |
| − | == Wiring == | + | == <translate><!--T:2--> |
| + | Wiring</translate> == | ||
| + | <translate><!--T:3--> | ||
Connect the cable according the photo. In the unit the cable is in the RUD port. In the receiver it is always the last channel. | Connect the cable according the photo. In the unit the cable is in the RUD port. In the receiver it is always the last channel. | ||
| − | For GR-12/GR-12L it is output with label | + | For GR-12/GR-12L it is output with label '''6'''.</translate> |
| + | {{Info|[[File:Info.png]] <translate><!--T:4--> | ||
| + | Please note that the signal wire (Orange) is at the bottom of the receiver.</translate>}} | ||
[[File:sumd-conn.jpg|thumb|center|600px]] | [[File:sumd-conn.jpg|thumb|center|600px]] | ||
| − | If you have not connected a power supply, you can connect the BEC cable or 1-2S LiPol now (even without a servos). | + | <translate><!--T:5--> |
| − | + | If you have not connected a power supply, you can connect the BEC cable or 1-2S LiPol now (even without a servos).</translate> | |
| − | + | {{Quote|'''<translate><!--T:6--> | |
| + | Never connect a power supply to the SYS or ELE/PIT/AIL ports!</translate>'''}} | ||
| + | == <translate><!--T:7--> | ||
| + | Spirit Settings</translate> == | ||
| + | |||
| + | <translate><!--T:8--> | ||
After initialization of the unit you can start the software. | After initialization of the unit you can start the software. | ||
| − | To allow the connection set the Receiver type to SRXL/SUMD in the General tab. | + | To allow the connection set the Receiver type to SRXL/SUMD in the General tab.</translate> |
[[File:sumd-settings.png|thumb|center]] | [[File:sumd-settings.png|thumb|center]] | ||
| − | Now save the settings (''CTRL+S'') or in the ''Backup tab/Unit - Save''. | + | <translate><!--T:9--> |
| + | Now save the settings (''CTRL+S'') or in the ''Backup tab/Unit - Save''.</translate> | ||
| − | == Receiver configuration == | + | == <translate><!--T:10--> |
| + | Receiver configuration</translate> == | ||
| + | <translate><!--T:11--> | ||
By default SUMD transmission is disabled in the HoTT receivers. | By default SUMD transmission is disabled in the HoTT receivers. | ||
| − | It is necessary to enable it in the ''(F) Function/Telemetry/Setting & Data View'' menu. | + | It is necessary to enable it in the ''(F) Function/Telemetry/Setting & Data View'' menu (HoTT MZ series).</translate><br/> |
| − | Change ''SUMD at CH6'' to ''YES''. | + | <translate><!--T:12--> |
| + | Change ''SUMD at CH6'' to ''YES''.</translate> | ||
[[File:sumd-rx.jpg|thumb|center]] | [[File:sumd-rx.jpg|thumb|center]] | ||
| − | == Usage == | + | == <translate><!--T:13--> |
| + | Usage</translate> == | ||
| + | <translate><!--T:14--> | ||
Now you can restart the unit. After the initialization the SUMD connection will work. | Now you can restart the unit. After the initialization the SUMD connection will work. | ||
| − | Reverse of some channels might be necessary depending on the radio model - please check the Diagnostic tab. | + | Reverse of some channels might be necessary depending on the radio model - please check the Diagnostic tab.</translate> |
| + | |||
| + | <translate><!--T:15--> | ||
| + | The transmission is able to carry all the channels. Usually ''SUMDOF12'' option (if available) is fine.</translate> | ||
| − | + | {{Info|[[File:Info.png|18px|]] <translate><!--T:16--> | |
| + | For '''MX-12/MZ-12 transmitters''' it is needed to change the channel mapping in the Spirit Settings. Please go to the ''General tab/Channels'' and change '''Gyro Gain''' to ''Channel 7''.</translate>}} | ||
Latest revision as of 12:20, 4 April 2017
With Graupner HoTT radios you can use fully digital, single-line SUMD protocol. For the connection only normal servo cable is required.
1 Wiring
Connect the cable according the photo. In the unit the cable is in the RUD port. In the receiver it is always the last channel. For GR-12/GR-12L it is output with label 6.
Please note that the signal wire (Orange) is at the bottom of the receiver.
If you have not connected a power supply, you can connect the BEC cable or 1-2S LiPol now (even without a servos).
Never connect a power supply to the SYS or ELE/PIT/AIL ports!
2 Spirit Settings
After initialization of the unit you can start the software. To allow the connection set the Receiver type to SRXL/SUMD in the General tab.
Now save the settings (CTRL+S) or in the Backup tab/Unit - Save.
3 Receiver configuration
By default SUMD transmission is disabled in the HoTT receivers.
It is necessary to enable it in the (F) Function/Telemetry/Setting & Data View menu (HoTT MZ series).
Change SUMD at CH6 to YES.
4 Usage
Now you can restart the unit. After the initialization the SUMD connection will work. Reverse of some channels might be necessary depending on the radio model - please check the Diagnostic tab.
The transmission is able to carry all the channels. Usually SUMDOF12 option (if available) is fine.
