Difference between revisions of "Problems and Solutions"
From Spirit System Manual
| (13 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
<div id="up"></div> | <div id="up"></div> | ||
| − | + | {| class="problems" style="text-align: left; width: 100%;" | |
| − | {| class="problems" style="text-align: left; width: | + | |
|'''<translate><!--T:1--> | |'''<translate><!--T:1--> | ||
Problem description</translate>''' | Problem description</translate>''' | ||
| Line 20: | Line 19: | ||
|- style="vertical-align:top;" | |- style="vertical-align:top;" | ||
|<translate><!--T:6--> | |<translate><!--T:6--> | ||
| − | Aggressive cyclic pitch movement or fast forward flight leads to rapid, large tail oscillations</translate> | + | Aggressive cyclic, collective pitch movement or fast forward flight leads to rapid, large tail oscillations</translate> |
|<translate><!--T:7--> | |<translate><!--T:7--> | ||
Decrease pirouette consistency in the ''Advanced tab'' gradually by 10 until this disappears. Check the tail mechanics for binding.</translate> | Decrease pirouette consistency in the ''Advanced tab'' gradually by 10 until this disappears. Check the tail mechanics for binding.</translate> | ||
| Line 33: | Line 32: | ||
|<translate><!--T:11--> | |<translate><!--T:11--> | ||
Decrease gyro gain in the transmitter.</translate> | Decrease gyro gain in the transmitter.</translate> | ||
| + | |- style="vertical-align:top;" | ||
| + | |<translate><!--T:40--> | ||
| + | Flips and rolls are too slow or too fast</translate> | ||
| + | |<translate><!--T:41--> | ||
| + | Increase/decrease rotation speed for Cyclic in the ''Sensor tab''.</translate> | ||
|- style="vertical-align:top;" | |- style="vertical-align:top;" | ||
|<translate><!--T:12--> | |<translate><!--T:12--> | ||
| − | + | Pirouette is too slow/fast</translate> | |
|<translate><!--T:13--> | |<translate><!--T:13--> | ||
| − | Increase/decrease rotation speed for | + | Increase/decrease rotation speed for Rudder in the ''Sensor tab''.</translate> |
|- style="vertical-align:top;" | |- style="vertical-align:top;" | ||
|<translate><!--T:14--> | |<translate><!--T:14--> | ||
| Line 68: | Line 72: | ||
|<translate><!--T:25--> | |<translate><!--T:25--> | ||
The unit was started with the Rescue mode engaged. Turn off the rescue from your transmitter.</translate> | The unit was started with the Rescue mode engaged. Turn off the rescue from your transmitter.</translate> | ||
| − | | | + | |- style="vertical-align:top;" |
|<translate><!--T:26--> | |<translate><!--T:26--> | ||
Rudder stop is not equal for both sides</translate> | Rudder stop is not equal for both sides</translate> | ||
|<translate><!--T:27--> | |<translate><!--T:27--> | ||
Check rudder servo center position, rudder mechanics. You can also try to lower rudder limit for the side where bounce-back occur.</translate> | Check rudder servo center position, rudder mechanics. You can also try to lower rudder limit for the side where bounce-back occur.</translate> | ||
| + | |- style="vertical-align:top;" | ||
| + | |<translate><!--T:34--> | ||
| + | Positive and negative collective pitch is unequal</translate> | ||
| + | |<translate><!--T:35--> | ||
| + | Enable Servos/Subtrim (tuning) and verify that servo arms are perpendicular, swashplate perfectly leveled and there is 0° between main blades. If yes, use the Servo Travel Correction.</translate> | ||
| + | |- style="vertical-align:top;" | ||
| + | |<translate><!--T:36--> | ||
| + | Castle ESC is not arming</translate> | ||
| + | |<translate><!--T:37--> | ||
| + | Set ''General - Throttle/Governor - Throttle Range Min.'' to 1060µs and ''Max.'' to 1940µs.</translate> | ||
| + | |- style="vertical-align:top;" | ||
| + | |<translate><!--T:38--> | ||
| + | RPM readout is not correct with the ESC Telemetry</translate> | ||
| + | |<translate><!--T:39--> | ||
| + | Temporarily enable ''General - Throttle/Governor - Governor'' and set ''Sensing Divider'' and ''Gear Ratio''. Then turn the Governor off if governor from ESC is used.</translate> | ||
|} | |} | ||
| − | |||
<div class=noprint> | <div class=noprint> | ||
Latest revision as of 15:04, 19 August 2023
| Problem description | Solution |
| Swashplate or tail drifts after initialization | Check trims and subtrims. Sticks in neutral position must be 0%, see the Diagnostics tab. Increase Stick deadband in Advanced tab. |
| Rudder or cyclic is not precise | Increase cyclic gain and/or increase the gyro gain in the transmitter. Add exponential in the transmitter. |
| Aggressive cyclic, collective pitch movement or fast forward flight leads to rapid, large tail oscillations | Decrease pirouette consistency in the Advanced tab gradually by 10 until this disappears. Check the tail mechanics for binding. |
| Model oscillates in elevator or aileron axes | Decrease cyclic gain in Sensor tab. |
| Tail oscillates rapidly | Decrease gyro gain in the transmitter. |
| Flips and rolls are too slow or too fast | Increase/decrease rotation speed for Cyclic in the Sensor tab. |
| Pirouette is too slow/fast | Increase/decrease rotation speed for Rudder in the Sensor tab. |
| Servos jitter randomly without external influences | Check the cable connection between the receiver and the unit. |
| During stationary pirouettes model drifts | Check the Subtrim configuration in the Servos tab. It seems to be inprecise. |
| Aggressive elevator stick movement leads to bouncing | Increase elevator filter in Advanced tab and/or decrease cyclic feed forward in Advanced tab. |
| Cyclic feel is delayed or disconnected | Increase cyclic feed forward in Advanced tab. |
| Elevator servo is not moving when initialization is finished | Flight log from the previous flight was saved. View the log in the Diagnostic tab and fix reported problem. |
| Swashplate is jumping in a cycle when initialization is finished | The unit was started with the Rescue mode engaged. Turn off the rescue from your transmitter. |
| Rudder stop is not equal for both sides | Check rudder servo center position, rudder mechanics. You can also try to lower rudder limit for the side where bounce-back occur. |
| Positive and negative collective pitch is unequal | Enable Servos/Subtrim (tuning) and verify that servo arms are perpendicular, swashplate perfectly leveled and there is 0° between main blades. If yes, use the Servo Travel Correction. |
| Castle ESC is not arming | Set General - Throttle/Governor - Throttle Range Min. to 1060µs and Max. to 1940µs. |
| RPM readout is not correct with the ESC Telemetry | Temporarily enable General - Throttle/Governor - Governor and set Sensing Divider and Gear Ratio. Then turn the Governor off if governor from ESC is used. |
