Difference between revisions of "Wiring/fr"

From Spirit System Manual
Jump to: navigation, search
(Created page with "– type de recepteur: PWM")
(Created page with "Pour les récepteurs standards, il est nécessaire d'utiliser 2 câbles normaux et un câble spécial. Les 3 connecteurs du câble spécial doivent être branchés sur le réc...")
Line 90: Line 90:
  
  
−
For standard receivers it is necessary to use two normal and one special cable. Three connectors from the special cable should be plugged into the receiver and the end of this cable to the unit.
+
Pour les récepteurs standards, il est nécessaire d'utiliser 2 câbles normaux et un câble spécial. Les 3 connecteurs du câble spécial doivent être branchés sur le récepteur et l'autre côté sur le module.
  
 
The unit is powered by two cables from the receiver connected to AUX and RUD positions. The Throttle cable should be connected to the receiver as well.
 
The unit is powered by two cables from the receiver connected to AUX and RUD positions. The Throttle cable should be connected to the receiver as well.

Revision as of 12:42, 20 September 2016

Other languages:
čeština • ‎Deutsch • ‎English • ‎español • ‎français • ‎magyar • ‎italiano • ‎русский • ‎中文（繁體）‎

Le Spirit peut être utilisé comme un gyroscope dédié à l'anticouple ou bien comme un système flybarless. Le câblage du module dépend du type de récepteur utilisé.

NOTE
Le Spirit est pré-programmé pour utiliser des servos avec un neutre à 1520µs et une fréquence de 50Hz. Veuillez vous assurer que les paramètres de servos sont conformes à ceux spécifiés par le fabriquant. Si le neutre d'un de vos servos est différent, comme 760µs, ne le connectez pas maintenant parce qu'il pourrait être endommagé.


Certains connecteurs ont des dimensions non standard qui pourraient gêner les connecteur adjacents. Nous recommendons dans ce cas de remplacer ces connecteurs non standards par des connecteurs de type JR ou Futaba.


Ne branchez jamais un connecteur pour alimenter le module dans les positions SYS ou ELE/PIT/TAIL. Vous risquez d'endommager le module.


1 GYROSCOPE AUTONOME ET BARRE DE BELL

Les possesseurs d'hélicoptères à barre de Bell peuvent utiliser le gyroscope à conservateur de cap, qui garde la direction de l'anti-couple donnée par l'émetteur quelques soient les effets du vent ou de forces extérieures.

Connectez le servo d'anti-couple au port "CH4" du module Spirit. Si vous utilisez aussi un récepteur standard, vous aurez besoin de connecter la voie GEAR (ou AUX) de votre récepteur au port AUX du module Spirit. Vous devrez aussi connecter le port RUD de votre récepteur au port RUD du module Spirit.

Même si vous avez un hélicoptère à barre de Bell, vous pouvez connecter le module de la même manière qu'avec un hélicoptère flybarless. Cela permet d'utiliser tout le potentiel du module comme la Stabilisation et le mode Sauvetage. Pour que ceci fonctionne correctement, il est nécessaire ce cocher "Flybar mechanic" dans l'onglet Stabi durant la configuration. Tous les autres paramètre peuvent être ajustés de la même façon que sur une tête flybarless.


2 FLYBARLESS

Les hélicoptères flybarless peuvent tirer partie de toutes les possibilités du module Spirit. Le Spirit va stabiliser le modèle sur tout les axes et le rendra aussi moins sensible au vent. Il étendra son temps de vol et augmentera son l'agilité. S'il est configuré correctement, le vol sera plus agréable ce qui vous donnera la confiance pour tenter des manoeuvre plus difficiles.

Les pales flybarless sont aussi différentes des pales conçues pour les modèles à barre de Bell. Pour de performance de vol optimum il est recommandé de les utiliser. Lors de l'utilisation du Spirit sur un système flybarless, tous les servos devraient être connectés aux position appropriées. Voir la description qui suit:


Spirit
CH1 – Servo de Pas / Aileron
CH2 – Servo de profondeur
CH3 – Servo d'Aileron/Pas
CH4 – Servo d'anti-couple


Spirit Pro
CH1 – Servo de Pas / Aileron
CH2 – Servo de profondeur
CH3 – Servo d'Aileron / Pas
CH4 – Servo d'anti-couple
CH0 – Servo de cyclique auxiliaire (optionnel) pour les plateaux cyclique de type CCPM 90


NOTE
Les servos connectés à CH1 et CH3 dépendent de la configuration du plateau cyclique. Le servo d'Aileron est le plus souvent du côté droit, tandis que le servo de Pas est du côté gauche.


3 CONNECTION D'UN RECEPTEUR STANDARD (PWM)

Pwms.png

Spirit – type de recepteur: PWM


Pwm.png

Spirit Pro – type de recepteur: PWM


Pour les récepteurs standards, il est nécessaire d'utiliser 2 câbles normaux et un câble spécial. Les 3 connecteurs du câble spécial doivent être branchés sur le récepteur et l'autre côté sur le module.

The unit is powered by two cables from the receiver connected to AUX and RUD positions. The Throttle cable should be connected to the receiver as well.

The easiest way you can start connect RUD with Rudder output in the receiver. Then continue with AUX which should be connected to the Gyro Gain channel output. Next, connect the Aileron, Elevator and Pitch (Aileron 2) channels. If you are not sure whether you have the correct output or not, you can plug in one servo and power the unit to verify that your connection is correct. This can be repeated for each servo. The diagnostics tab is very helpful too.

Spirit Pro
The unit is able to control Bank Switching by 7th channel of the receiver. Connect the cable to the AUX2 port and allow Bank Switching in the software.


Never plug a connector for powering the unit to SYS or ELE/PIT/AIL ports.


4 CONNECTION OF SPEKTRUM DSM2/X SATELLITE

Bind.png

Spirit – receiver type: Spektrum DSM2/X


Satellite.png

Spirit Pro – receiver type: Spektrum DSM2/X


Connection to a BEC is optional. If the model is powered by an external BEC, this must be connected to the RUD port. Also the power lead from the ESCs internal BEC must be disconnected.

Spirit
A second satellite can be connected, but this can only be achieved via a special adapter connected to the RUD port. This adapter can be purchased separately. Before satellites can be used they must be bound to your transmitter, taking into account any failsafes that need to be set. To use both, two satellites and an external BEC, be sure to use a Y-harness made from large gauge wire to supply the high current that is needed.


Spirit Pro
The Pro version allows you to connect two satellites directly to the unit. If you want to use only one satellite, you have to use the Primary connector.


To bind the satellites, insert a bind plug in the SYS port for DSM2 satellites or the ELE/PIT/AIL port for DSMX satellites. Power cycling the Spirit start the bind process. Once successfully bound, the STATUS LED will go out and the satellite LED will come on. If the second satellite fails to bind, swap the satellites and repeat the bind process.

Be sure Receiver type in the software is configured to Spektrum DSM2/X or else binding process will not work. Never plug a connector for powering the unit to SYS or ELE/PIT/AIL positions.


5 CONNECTION OF FUTABA S-BUS RECEIVER

Spirit sbus.png

Spirit – receiver type: Futaba S-BUS


S-BUS.png

Spirit Pro – receiver type: Futaba S-BUS


Spirit
When using S-BUS it is necessary to use an inverter that replaces the cable between the receiver and the Spirit unit's RUD port. This inverter cable can be purchased separately. The inverter cable have to be connected in the way, that longer end is directed to the unit and shorter to the receiver.


Spirit Pro
Connect the receiver with the unit by normal patch cable to the RUD port. You can use cable that is included in the package.


Connection to a BEC is optional. For models of 500 size and larger it is recommended to use dual power supply cables due to the increased power consumption. That means besides the S-BUS cable, an additional power supply cable should be connected to the AUX port.

When using this type of receiver you can connect the throttle cable directly to the receiver. Alternatively, you can assign the throttle channel in the software and use the AUX as throttle output from the unit.


Never plug a connector for powering the unit to SYS or ELE/PIT/AIL ports.


6 CONNECTION OF PPM RECEIVER

Spirit ppm.png

Spirit – receiver type: PPM


PPM.png

Spirit Pro – receiver type: PPM


NOTE
Connection to a BEC is optional. For models of 500 size and larger it is recommended to use dual power supply cables due to the increased power consumption. That means besides the communication cable, an additional power supply cable should be connected to the AUX port.

When using this type of receiver you can connect the throttle cable directly to the receiver. Alternatively, you can assign the throttle channel in the software and use the AUX as throttle output from the unit.


Never plug a connector for powering the unit to SYS or ELE/PIT/AIL ports.


7 CONNECTION OF JETI EX BUS RECEIVER

Spirit exbus.png

Spirit – receiver type: Jeti EX Bus


EX-BUS.png

Spirit Pro – receiver type: Jeti EX Bus


This connection type now supports the new integration with JETI Model transmitters. You can now fully configure the Spirit unit remotely through the JETI Model transmitter.

Remember to configure the receiver type through the software or the integration will not work. Also, it is necessary to download Spirit.bin file from the website. Move the file to the Devices directory in the SD card of your transmitter.


NOTE
Connection to a BEC is optional. For models of 500 size and larger it is recommended to use dual power supply cables due to the increased power consumption. That means besides the EX Bus cable, an additional power supply cable should be connected to the AUX port.

When using this type of receiver you can connect the throttle cable directly to the receiver. Alternatively, you can assign the throttle channel in the software and use the AUX as throttle output from the unit.


A special cable is needed to enable this communication.

Never plug a connector for powering the unit to SYS or ELE/PIT/AIL ports.


8 CONNECTION OF SRXL/SUMD RECEIVER

Spirit srxl.png

Spirit – receiver type: SRXL/SUMD


SRXL.png

Spirit Pro – receiver type: SRXL/SUMD


NOTE
Connection to a BEC is optional. For models of 500 size and larger it is recommended to use dual power supply cables due to the increased power consumption. That means besides the communication cable, an additional power supply cable should be connected to the AUX port. This protocol family can work with a wide range of receivers. Thus you can use Multiplex SRXL, BeastX SRXL, Graupner SUMD, Jeti UDI, Spektrum SRXL and more.

When using this type of receiver you can connect the throttle cable directly to the receiver. Alternatively, you can assign the throttle channel in the software and use the AUX as throttle output from the unit.


Never plug a connector for powering the unit to SYS or ELE/PIT/AIL ports.


9 CONNECTOR ORIENTATION

All cables connected to the unit must be oriented so that the signal wire (Lightest color wire) is closer to the connector pin label, towards the center of the unit. This orients the negative (darkest color wire) toward the edge of the unit.


← Installation ↑Up↑ Configuration →
Retrieved from "https://manual.spirit-system.com/index.php?title=Wiring/fr&oldid=5026"