Difference between revisions of "GeoLink Troubleshooting/es"
(Created page with "GEOLINK") |
(Updating to match new version of source page) |
||
| (6 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
<languages /> | <languages /> | ||
| + | |||
| + | == Precision == | ||
| + | |||
| + | If you are encountering precision problem of a GeoLink feature, please read the following sections. | ||
| + | |||
| + | === Drifting === | ||
| + | |||
| + | If model is drifting after engaging Position Hold, Return to Home or GeoFence feature it is required to make sure that: | ||
| + | * GeoLink Compass Calibration is performed correctly. | ||
| + | * Stabilisation mode such as Stabilisation (Normal), Stabilisation (Acro), Coaxial is not drifting even after prolonged flight time. | ||
| + | |||
| + | ==== Incorrect Compass Calibration ==== | ||
| + | |||
| + | Incorrect Calibration can be distinguished with GeoLink Position Hold in the easiest way. | ||
| + | We recommend to engage the feature in a safe altitude and then observe behavior of the model. | ||
| + | |||
| + | If model will start to make a circles then Compass Calibration is wrong. If even Calibration at the flying field will not help, the problem can be alternatively fixed by adjusting '''Compass Heading Correction''' parameter. | ||
| + | |||
| + | The model must stay stationary with no aileron/elevator movement when everything is correct. | ||
| + | |||
| + | If model will fly away more than 5 meters immediately disengage the feature and land. Proceed according following subsection. | ||
| + | |||
| + | ==== Stabilisation drift ==== | ||
| + | |||
| + | Please make sure that Stabilisation is working precisely prior usage of a GeoLink features. This is very important as GeoLink is based on the Stabilisation feature. | ||
| + | We recommend to set Coaxial mode while GeoLink support can be disabled for testing. | ||
| + | |||
| + | The most common reason for drifting is incorrect mechanical setup - mainly servos are not centered properly. | ||
| + | There is very simple test to check if your setup is correct: | ||
| + | # Enable Servos / Subtrim (tuning) | ||
| + | # At this point all servo arms must be in the center of their travel range. As close as possible - any visible deflection is not correct. | ||
| + | # At the same time swashplate must be perfectly level - you can check it really precisely only with Cyclic Leveler tool. | ||
| + | # At the same time there must be 0° between main blades. You can fold ends of the main blades so they are near each other. They must be at the same height wherever you will rotate with main shaft. | ||
| + | # Only after checking that all 3 are correct, verify that Geometry 6° parameter is configured precisely. | ||
| + | |||
| + | Other reasons for imprecision are ESC fan (mainly from HobbyWing ESCs) or extremely high vibration level. | ||
| + | |||
| + | It is possible to setup the model and get it into a flying condition with relatively good results even with base settings all wrong. This mean that in a certain combination of wrong '''Mounting Position''', '''Swashplate type''', '''Servo reversing''' in the Spirit unit and '''Channel reversing''' in the radio, it is possible to make model to fly. But all Stabilisation and Rescue modes, including GeoLink features will work completely wrong. The easiest way to check if your base settings is in the Diagnostic tab. Make sure that all base channels are moving in the same direction as actual movement of the radio sticks. If they are moving all in a proper direction, your base settings are very likely correct. | ||
| + | |||
| + | You can fly with Coaxial mode, preferably for a longer time or at least near the end of the flight. Observe if model will not tilt to some side. Or that it is required to hold a sticks in order to stay stationary. | ||
| + | |||
| + | If yes, it is necessary to fix the problem. It can be fixed according following page: | ||
| + | [[Imprecise_Rescue|Imprecise Rescue or Stabilisation]] - '''Settings for the best performance''' section. | ||
| + | |||
| + | For GeoLink features to operate the most precisely '''Stabi Correction''' ON is the best option. Please note it is not possible to utilize this feature with all models - see the page above. | ||
| + | |||
| + | === Vertical pumping === | ||
| + | |||
| + | In some cases model could jump up and down having jerky and imprecse altitude hold. | ||
| + | This is mostly result of imprecise servo settings. | ||
| + | |||
| + | Please do the following checking: | ||
| + | # Enable Servos / Subtrim (tuning) | ||
| + | # At this point all servo arms must be in the center of their travel range. As close as possible - any visible deflection is not correct. | ||
| + | # At the same time swashplate must be perfectly level - you can check it really precisely only with Cyclic Leveler tool. | ||
| + | # At the same time there must be 0° between main blades. You can fold ends of the main blades so they are near each other. They must be at the same height wherever you will rotate with main shaft. | ||
| + | # Only after checking that all 3 are correct, verify that Geometry 6° parameter is configured precisely. | ||
| + | |||
| + | For some models it is needed to decrease '''Vertical Correction Gain''' if model is doing visible corrections. You can start with the lowest number and increase it by 10 points in that case. | ||
| + | |||
| + | == Fallos == | ||
En caso de un problema, GEOLINK notificara al piloto mediante un LED de estado incorporado. | En caso de un problema, GEOLINK notificara al piloto mediante un LED de estado incorporado. | ||
| Line 6: | Line 67: | ||
El parpadeo de LED puede aparacer inmediatamente despues del encendido. Por numero de parpadeos de LED en serie, puede determinar que problema esta presente. | El parpadeo de LED puede aparacer inmediatamente despues del encendido. Por numero de parpadeos de LED en serie, puede determinar que problema esta presente. | ||
| − | |||
| − | |||
=== 1x parpadeo === | === 1x parpadeo === | ||
| Line 29: | Line 88: | ||
=== Parpadeo constante === | === Parpadeo constante === | ||
| − | + | This might happen rather in-flight and could signalize unexpected failure. Most probable reason is shock by high electrostatic discharge. This will result in the '''GeoLink connection is broken event''' and loss of GeoLink functionality from the moment it will occur. | |
| + | Please make sure that there are no excess electrostatic discharges - check ground continuity between motor and tail boom. | ||
| + | You can also try to turn off GeoLink logging feature. | ||
| + | |||
| + | If you can't resolve this problem, we also recommend to Clear flight logs. | ||
| + | |||
| + | we recommend also to turn off GeoLink Logging feature first. GeoLink will not access to the FLASH memory and will be more immune to the static discharges. | ||
| + | |||
| + | Updating to the latest Spirit and GeoLink firmware is always recommended as precaution to any problem. | ||
== Otras notificaciones == | == Otras notificaciones == | ||
| Line 37: | Line 104: | ||
=== Proceso de calibracion === | === Proceso de calibracion === | ||
| − | + | If you can see 3 series of fast flashing (followed by fast erratic blinks) after power up of the GeoLink then the module is in so called Calibration process. | |
| − | + | This process can be invoked by pilot through the Spirit Settings software and must be finished according [http://manual.spirit-system.com/index.php?title=GeoLink_Configuration#Compass_Calibration instructions]. | |
| − | + | Until finished the GeoLink will be inoperable. Spirit Settings will display '''Not connected''' message until the calibration is finished. | |
| − | + | ||
<div class=noprint> | <div class=noprint> | ||
| Line 48: | Line 114: | ||
| style="width: 33%;"| [[configuracion_GEOLINK|← Configuracion]] | | style="width: 33%;"| [[configuracion_GEOLINK|← Configuracion]] | ||
| style="width: 33%;text-align:center;"| [[#up|↑Arriba↑]] | | style="width: 33%;text-align:center;"| [[#up|↑Arriba↑]] | ||
| − | | style="text-align:right;" | [[GEOLINK| | + | | style="text-align:right;" | [[GEOLINK|GEOLINK →]] |
|} | |} | ||
---- | ---- | ||
</div> | </div> | ||
Latest revision as of 11:57, 18 August 2023
Contents
1 Precision
If you are encountering precision problem of a GeoLink feature, please read the following sections.
1.1 Drifting
If model is drifting after engaging Position Hold, Return to Home or GeoFence feature it is required to make sure that:
- GeoLink Compass Calibration is performed correctly.
- Stabilisation mode such as Stabilisation (Normal), Stabilisation (Acro), Coaxial is not drifting even after prolonged flight time.
1.1.1 Incorrect Compass Calibration
Incorrect Calibration can be distinguished with GeoLink Position Hold in the easiest way. We recommend to engage the feature in a safe altitude and then observe behavior of the model.
If model will start to make a circles then Compass Calibration is wrong. If even Calibration at the flying field will not help, the problem can be alternatively fixed by adjusting Compass Heading Correction parameter.
The model must stay stationary with no aileron/elevator movement when everything is correct.
If model will fly away more than 5 meters immediately disengage the feature and land. Proceed according following subsection.
1.1.2 Stabilisation drift
Please make sure that Stabilisation is working precisely prior usage of a GeoLink features. This is very important as GeoLink is based on the Stabilisation feature. We recommend to set Coaxial mode while GeoLink support can be disabled for testing.
The most common reason for drifting is incorrect mechanical setup - mainly servos are not centered properly. There is very simple test to check if your setup is correct:
- Enable Servos / Subtrim (tuning)
- At this point all servo arms must be in the center of their travel range. As close as possible - any visible deflection is not correct.
- At the same time swashplate must be perfectly level - you can check it really precisely only with Cyclic Leveler tool.
- At the same time there must be 0° between main blades. You can fold ends of the main blades so they are near each other. They must be at the same height wherever you will rotate with main shaft.
- Only after checking that all 3 are correct, verify that Geometry 6° parameter is configured precisely.
Other reasons for imprecision are ESC fan (mainly from HobbyWing ESCs) or extremely high vibration level.
It is possible to setup the model and get it into a flying condition with relatively good results even with base settings all wrong. This mean that in a certain combination of wrong Mounting Position, Swashplate type, Servo reversing in the Spirit unit and Channel reversing in the radio, it is possible to make model to fly. But all Stabilisation and Rescue modes, including GeoLink features will work completely wrong. The easiest way to check if your base settings is in the Diagnostic tab. Make sure that all base channels are moving in the same direction as actual movement of the radio sticks. If they are moving all in a proper direction, your base settings are very likely correct.
You can fly with Coaxial mode, preferably for a longer time or at least near the end of the flight. Observe if model will not tilt to some side. Or that it is required to hold a sticks in order to stay stationary.
If yes, it is necessary to fix the problem. It can be fixed according following page: Imprecise Rescue or Stabilisation - Settings for the best performance section.
For GeoLink features to operate the most precisely Stabi Correction ON is the best option. Please note it is not possible to utilize this feature with all models - see the page above.
1.2 Vertical pumping
In some cases model could jump up and down having jerky and imprecse altitude hold. This is mostly result of imprecise servo settings.
Please do the following checking:
- Enable Servos / Subtrim (tuning)
- At this point all servo arms must be in the center of their travel range. As close as possible - any visible deflection is not correct.
- At the same time swashplate must be perfectly level - you can check it really precisely only with Cyclic Leveler tool.
- At the same time there must be 0° between main blades. You can fold ends of the main blades so they are near each other. They must be at the same height wherever you will rotate with main shaft.
- Only after checking that all 3 are correct, verify that Geometry 6° parameter is configured precisely.
For some models it is needed to decrease Vertical Correction Gain if model is doing visible corrections. You can start with the lowest number and increase it by 10 points in that case.
2 Fallos
En caso de un problema, GEOLINK notificara al piloto mediante un LED de estado incorporado. cualquier falla es señalada por un LED de estado parpadeante que se repite periodicamente. Si se produjo algun problema despues de una falla, se requiere la reparacion de GEOLINK.
El parpadeo de LED puede aparacer inmediatamente despues del encendido. Por numero de parpadeos de LED en serie, puede determinar que problema esta presente.
2.1 1x parpadeo
Los datos de hardware almacenados en GEOLINK se perdieron.Es necesario contactar con el apoyo del sistema SPIRIT.
2.2 2X PARPADEOS
El sensor de presion no esta funcionando correctamente. Por lo general, este problema ocurre cuando GEOLINK funciona durante un tiempo prolongado en condiciones de humedad extremadamente alta. Almacene GEOLINK en un ambiente de baja humedad durante unas pocas horas hasta que el condensado interno se evapore. Si esto no te ayuda, contacta con el soporte del sistema SPIRIT.
2.3 3X parpadeos
Giroscopios, los sensores del acelerometro no funcionan correctamente. Es necesario contactar con el apoyo del sistema SPIRIT.
2.4 4X parpadeos
El sensor de la brujula no funciona correctamente. Es necesario contactar con el apoyo del sistema SPIRIT.
2.5 Parpadeo constante
This might happen rather in-flight and could signalize unexpected failure. Most probable reason is shock by high electrostatic discharge. This will result in the GeoLink connection is broken event and loss of GeoLink functionality from the moment it will occur. Please make sure that there are no excess electrostatic discharges - check ground continuity between motor and tail boom. You can also try to turn off GeoLink logging feature.
If you can't resolve this problem, we also recommend to Clear flight logs.
we recommend also to turn off GeoLink Logging feature first. GeoLink will not access to the FLASH memory and will be more immune to the static discharges.
Updating to the latest Spirit and GeoLink firmware is always recommended as precaution to any problem.
3 Otras notificaciones
En caso de que GEOLINK este destellando y el piloto no pueda acceder a el a traves de la configuracion del SPIRIT, la siguiente puede ser la razon
3.1 Proceso de calibracion
If you can see 3 series of fast flashing (followed by fast erratic blinks) after power up of the GeoLink then the module is in so called Calibration process. This process can be invoked by pilot through the Spirit Settings software and must be finished according instructions. Until finished the GeoLink will be inoperable. Spirit Settings will display Not connected message until the calibration is finished.
